40 CFR Part 1048 — Control of Emissions from New, Large Nonroad Spark-Ignition Engines

PART 1048—CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-IGNITION ENGINES Authority: 42 U.S.C. 7401-7671q. Source: 67 FR 68347, Nov. 8, 2002, unless otherwise noted. Subpart A—Overview and Applicability § 1048.1 Does this part apply to me? (a) The regulations in this part 1048 apply for all new, spark-ignition nonroad engines (defined in § 1048.801) with maximum engine power above 19 kW, except as provided in § 1048.5. (b) This part 1048 applies for engines built on or after January 1, 2004. You need not follow this part for engines you produce before January 1, 2004. See (c) The definition of nonroad engine in 40 CFR 1068.30 excludes certain engines used in stationary applications. These engines may be required by 40 CFR part 60, subpart JJJJ, to comply with some of the provisions of this part 1048; otherwise, these engines are only required to comply with the requirements in § 1048.20. In addition, the prohibitions in 40 CFR 1068.101 restrict the use of stationary engines for nonstationary purposes unless they are certified under this part 1048 to the same standards that would apply to nonroad engines for the same model year. (d) In certain cases, the regulations in this part 1048 apply to engines with maximum engine power at or below 19 kW that would otherwise be covered by 40 CFR part 90 or 1054. See 40 CFR 90.913 or 1054.615 for provisions related to this allowance. [70 FR 40465, July 13, 2005, as amended at 73 FR 3613, Jan. 18, 2008; 73 FR 59231, Oct. 8, 2008] § 1048.2 Who is responsible for compliance? The regulations in this part 1048 contain provisions that affect both engine manufacturers and others. However, the requirements of this part are generally addressed to the engine manufacturer. The term “you” generally means the engine manufacturer, as defined in § 1048.801, especially for issues related to certification (including production-line testing, reporting, etc.). [73 FR 59231, Oct. 8, 2008] § 1048.5 Which engines are excluded from this part's requirements? This part does not apply to the following nonroad engines: (a) Engines that are certified to meet the requirements of 40 CFR part 1051, or are otherwise subject to 40 CFR part 1051 (for example, engines used in snowmobiles and all-terrain vehicles). (b) Propulsion marine engines. See 40 CFR parts 91 and 1045. This part applies with respect to auxiliary marine engines. (c) Engines that are certified to meet the requirements of 40 CFR parts 92 or 1033 (locomotive engines), or are otherwise subject to 40 CFR parts 92 or 1033. [70 FR 40465, July 13, 2005, as amended at 73 FR 59232, Oct. 8, 2008] § 1048.10 How is this part organized? This part 1048 is divided into the following subparts: (a) Subpart A of this part defines the applicability of part 1048 and gives an overview of regulatory requirements. (b) Subpart B of this part describes the emission standards and other requirements that must be met to certify engines under this part. Note that § 1048.145 discusses certain interim requirements and compliance provisions that apply only for a limited time. (c) Subpart C of this part describes how to apply for a certificate of conformity. (d) Subpart D of this part describes general provisions for testing production-line engines. (e) Subpart E of this part describes general provisions for testing in-use engines. (f) Subpart F of this part describes how to test your engines (including references to other parts of the Code of Federal Regulations). (g) Subpart G of this part and 40 CFR part 1068 describe requirements, prohibitions, and other provisions that apply to engine manufacturers, equipment manufacturers, owners, operators, rebuilders, and all others. (h) [Reserved] (i) Subpart I of this part contains definitions and other reference information. [70 FR 40465, July 13, 2005, as amended at 73 FR 59232, Oct. 8, 2008] § 1048.15 Do any other regulation parts apply to me? (a) Part 1060 of this chapter describes standards and procedures for controlling evaporative emissions from engines fueled by gasoline or other volatile liquid fuels and the associated fuel systems. These requirements apply to engine manufacturers as specified in this part 1048. Part 1060 applies optionally for equipment manufacturers and fuel-system component manufacturers for certifying their products. (b) Part 1065 of this chapter describes procedures and equipment specifications for testing engines to measure exhaust emissions. Subpart F of this part 1048 describes how to apply the provisions of part 1065 of this chapter to determine whether engines meet the exhaust emission standards in this part. (c) The requirements and prohibitions of part 1068 of this chapter apply to everyone, including anyone who manufactures, imports, installs, owns, operates, or rebuilds any of the engines subject to this part 1048, or equipment containing these engines. Part 1068 of this chapter describes general provisions, including these seven areas: (1) Prohibited acts and penalties for engine manufacturers, equipment manufacturers, and others. (2) Rebuilding and other aftermarket changes. (3) Exclusions and exemptions for certain engines. (4) Importing engines. (5) Selective enforcement audits of your production. (6) Defect reporting and recall. (7) Procedures for hearings. (d) Other parts of this chapter apply if referenced in this part. [70 FR 40465, July 13, 2005, as amended at 73 FR 59232, Oct. 8, 2008; 74 FR 8426, Feb. 24, 2009; 75 FR 23021, Apr. 30, 2010] § 1048.20 What requirements from this part apply to excluded stationary engines? (a) You must add a permanent label or tag to each new engine you produce or import that is excluded under § 1048.1(c) as a stationary engine and is not required by 40 CFR part 60, subpart JJJJ, to meet the standards and other requirements of this part 1048 that are equivalent to the requirements applicable to nonroad SI engines for the same model year. To meet labeling requirements, you must do the following things: (1) Attach the label or tag in one piece so no one can remove it without destroying or defacing it. (2) Secure it to a part of the engine needed for normal operation and not normally requiring replacement. (3) Make sure it is durable and readable for the engine's entire life. (4) Write it in English. (5) Follow the requirements in § 1048.135(g) regarding duplicate labels if the engine label is obscured in the final installation. (b) Engine labels or tags required under this section must have the following information: (1) Include the heading “EMISSION CONTROL INFORMATION”. (2) Include your full corporate name and trademark. You may instead include the full corporate name and trademark of another company you choose to designate. (3) State the engine displacement (in liters) and maximum engine power. (4) State: “THIS ENGINE IS EXCLUDED FROM THE REQUIREMENTS OF 40 CFR PART 1048 AS A “STATIONARY ENGINE” AND THE OWNER/OPERATOR MUST COMPLY WITH THE REQUIREMENTS OF 40 CFR PART 60. INSTALLING OR USING THIS ENGINE IN ANY OTHER APPLICATION MAY BE A VIOLATION OF FEDERAL LAW SUBJECT TO CIVIL PENALTY.”. (c) Stationary engines required by 40 CFR part 60, subpart JJJJ, to meet the requirements of this part 1048 must meet the labeling requirements of 40 CFR 60.4242. [70 FR 40466, July 13, 2005, as amended at 73 FR 3613, Jan. 18, 2008] § 1048.30 Submission of information. (a) This part includes various requirements to record data or other information. Refer to § 1048.825 and 40 CFR 1068.25 regarding recordkeeping requirements. Unless we specify otherwise, store these records in any format and on any media and keep them readily available for one year after you send an associated application for certification, or one year after you generate the data if they do not support an application for certification. You must promptly send us organized, written records in English if we ask for them. We may review them at any time. (b) The regulations in § 1048.255 and 40 CFR 1068.101 describe your obligation to report truthful and complete information and the consequences of failing to meet this obligation. This includes information not related to certification. (c) Send all reports and requests for approval to the Designated Compliance Officer ( see (d) Any written information we require you to send to or receive from another company is deemed to be a required record under this section. Such records are also deemed to be submissions to EPA. We may require you to send us these records whether or not you are a certificate holder. [75 FR 23021, Apr. 30, 2010] Subpart B—Emission Standards and Related Requirements § 1048.101 What exhaust emission standards must my engines meet? The exhaust emission standards of this section apply by model year. You may certify engines earlier than we require. The Tier 1 standards apply only to steady-state testing, as described in paragraph (b) of this section. The Tier 2 standards apply to steady-state, transient, and field testing, as described in paragraphs (a), (b), and (c) of this section. (a) Emission standards for transient testing. (1) Measure emissions using the applicable transient test procedures described in subpart F of this part. (2) The Tier 2 HC + NO X X (i) High-load engines. (ii) Engines with maximum engine power above 560 kW. (iii) Engines with maximum test speed above 3400 rpm. (iv) Constant-speed engines and severe-duty engines. (3) You may optionally certify your engines according to the following formula instead of the standards in paragraph (a)(1) of this section: (HC + NO X 0.784 X X Table 1 of § 1048.101—Examples of Possible Tier 2 Duty-cycle Emission Standards HC + NO X CO 2.7 4.4 2.2 5.6 1.7 7.9 1.3 11.1 1.0 15.5 0.8 20.6 (b) Standards for steady-state testing. (1) Measure emissions using the applicable steady-state test procedures described in subpart F of this part: (2) The following table shows the Tier 1 exhaust emission standards that apply to engines from 2004 through 2006 model years: Table 2 of § 1048.101—Tier 1 Emission Standards (g/kW-hr) Testing General emission standards Alternate emission standards for severe-duty engines HC + NO X CO HC + NO X CO Certification and production-line testing 4.0 50.0 4.0 130.0 In-use testing 5.4 50.0 5.4 130.0 (3) Starting in the 2007 model year, steady-state exhaust emissions from your engines may not exceed the numerical emission standards in paragraph (a) of this section. See paragraph (d) of this section for alternate standards that apply for certain engines. (c) Standards for field testing. (1) Measure emissions using the field-testing procedures in subpart F of this part: (2) The HC + NO X X (3) You may apply the following formula to determine alternate emission standards that apply to your engines instead of the standards in paragraph (c)(1) of this section: (HC + NO X 0.791 X Table 3 of § 1048.101—Examples of Possible Tier 2 Field-testing Emission Standards HC + NO X CO 3.8 6.5 3.1 8.5 2.4 11.7 1.8 16.8 1.4 23.1 1.1 31.0 (d) Engine protection. X (1) Show that enrichment is necessary to protect the engine from damage. (2) Show that you limit enrichment to operating modes that require additional cooling to protect the engine from damage. (3) Show in your application for certification that enrichment will rarely occur in use in the equipment in which your engines are installed. For example, an engine that is expected to operate 5 percent of the time in use with enrichment would clearly not qualify. (4) Include in your installation instructions any steps necessary for someone installing your engines to prevent enrichment during normal operation (see § 1048.130). (e) Fuel types. (1) Natural gas-fueled engines: NMHC emissions. (2) Alcohol-fueled engines: THCE emissions. (3) Other engines: THC emissions. (f) Small engines. (g) Useful life. (1) Specify a longer useful life in hours for an engine family under either of two conditions: (i) If you design, advertise, or market your engine to operate longer than the minimum useful life (your recommended hours until rebuild may indicate a longer design life). (ii) If your basic mechanical warranty is longer than the minimum useful life. (2) You may request in your application for certification that we approve a shorter useful life for an engine family. We may approve a shorter useful life, in hours of engine operation but not in years, if we determine that these engines will rarely operate longer than the shorter useful life. If engines identical to those in the engine family have already been produced and are in use, your demonstration must include documentation from such in-use engines. In other cases, your demonstration must include an engineering analysis of information equivalent to such in-use data, such as data from research engines or similar engine models that are already in production. Your demonstration must also include any overhaul interval that you recommend, any mechanical warranty that you offer for the engine or its components, and any relevant customer design specifications. Your demonstration may include any other relevant information. The useful life value may not be shorter than any of the following: (i) 1,000 hours of operation. (ii) Your recommended overhaul interval. (iii) Your mechanical warranty for the engine. (h) Applicability for testing. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40466, July 13, 2005; 73 FR 3613, Jan. 18, 2008; 73 FR 59232, Oct. 8, 2008] § 1048.105 What evaporative emission standards and requirements apply? Starting in the 2007 model year, new engines that run on a volatile liquid fuel (such as gasoline) must meet the emission standards of this section over a useful life of five years, except as specified in paragraph (f) of this section. Note that § 1048.245 allows you to use design-based certification instead of generating new emission data. (a) Fuel line permeation. (b) [Reserved] (c) Diurnal emissions. (d) Running loss. (e) Installation. (f) Motor vehicles and marine vessels. (1) Marine vessels using spark-ignition engines are subject to the requirements of 40 CFR part 1045. The vessels are not required to comply with the evaporative emission standards and related requirements of this part 1048. (2) Motor vehicles are subject to the requirements of 40 CFR part 86. They are not required to comply with the evaporative emission standards and related requirements of this part 1048. [73 FR 59232, Oct. 8, 2008, as amended at 78 FR 36396, June 17, 2013] § 1048.110 How must my engines diagnose malfunctions? The following engine-diagnostic requirements apply for engines equipped with three-way catalysts and closed-loop control of air-fuel ratios: (a) Equip your engines with a diagnostic system. (1) If your emission-control strategy depends on maintaining air-fuel ratios at stoichiometry, an acceptable diagnostic design would identify malfunction whenever the air-fuel ratio does not cross stoichiometry for one minute of intended closed-loop operation. You may use other diagnostic strategies if we approve them in advance. (2) If the protocol described in paragraph (a)(1) of this section does not apply to your engine, you must use an alternative approach that we approve in advance. Your alternative approach must generally detect when the emission-control system is not functioning properly. (b) Use a malfunction-indicator light (MIL). (1) When a malfunction occurs, as described in paragraph (a) of this section. (2) When the diagnostic system cannot send signals to meet the requirement of paragraph (b)(1) of this section. (3) When the engine's ignition is in the “key-on” position before starting or cranking. The MIL should go out after engine starting if the system detects no malfunction. (c) Control when the MIL can go out. (d) Store trouble codes in computer memory. (e) Make data, access codes, and devices accessible. (f) Consider exceptions for certain conditions. (g) Follow standard references for formats, codes, and connections. (1) ISO 9141-2 Road vehicles-Diagnostic systems—Part 2: CARB requirements for interchange of digital information, February 1994. (2) ISO 14230-4 Road vehicles—Diagnostic systems—Keyword Protocol 2000—Part 4: Requirements for emission-related systems, June 2000. [67 FR 68347, Nov. 8, 2002, as amended at 73 FR 59232, Oct. 8, 2008] § 1048.115 What other requirements apply? Engines that are required to meet the emission standards of this part must meet the following requirements: (a) Crankcase emissions. (1) Engines may discharge crankcase emissions to the ambient atmosphere if the emissions are added to the exhaust emissions (either physically or mathematically) during all emission testing. If you take advantage of this exception, you must do the following things: (i) Manufacture the engines so that all crankcase emissions can be routed into the applicable sampling systems specified in 40 CFR part 1065. (ii) Account for deterioration in crankcase emissions when determining exhaust deterioration factors. (2) For purposes of this paragraph (a), crankcase emissions that are routed to the exhaust upstream of exhaust aftertreatment during all operation are not considered to be discharged directly into the ambient atmosphere. (b) Torque broadcasting. (c) EPA access to broadcast information. (d) [Reserved] (e) Adjustable parameters. (f) Prohibited controls. (g) Defeat devices. (1) The conditions of concern were substantially included in the applicable test procedures described in subpart F of this part. (2) You show your design is necessary to prevent engine (or equipment) damage or accidents. (3) The reduced effectiveness applies only to starting the engine. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40467, July 13, 2005; 73 FR 59233, Oct. 8, 2008; 88 FR 4665, Jan. 24, 2023] § 1048.120 What emission-related warranty requirements apply to me? (a) General requirements. (1) It is designed, built, and equipped so it conforms at the time of sale to the ultimate purchaser with the requirements of this part. (2) It is free from defects in materials and workmanship that may keep it from meeting these requirements. (b) Warranty period. (c) Components covered. (d) Limited applicability. (e) Owners manual. [70 FR 40467, July 13, 2005, as amended at 73 FR 59233, Oct. 8, 2008; 75 FR 23021, Apr. 30, 2010] § 1048.125 What maintenance instructions must I give to buyers? Give the ultimate purchaser of each new nonroad engine written instructions for properly maintaining and using the engine, including the emission-control system. The maintenance instructions also apply to service accumulation on your emission-data engines, as described in 40 CFR part 1065. (a) Critical emission-related maintenance. (1) You demonstrate that the maintenance is reasonably likely to be done at the recommended intervals on in-use engines. We will accept scheduled maintenance as reasonably likely to occur if you satisfy any of the following conditions: (i) You present data showing that, if a lack of maintenance increases emissions, it also unacceptably degrades the engine's performance. (ii) You present survey data showing that at least 80 percent of engines in the field get the maintenance you specify at the recommended intervals. (iii) You provide the maintenance free of charge and clearly say so in your maintenance instructions (iv) You otherwise show us that the maintenance is reasonably likely to be done at the recommended intervals. (2) You may not schedule critical emission-related maintenance more frequently than the following minimum intervals, except as specified in paragraphs (a)(3), (b) and (c) of this section: (i) For catalysts, fuel injectors, electronic control units, superchargers, and turbochargers: The useful life of the engine family. (ii) For gaseous fuel-system components (cleaning without disassembly only) and oxygen sensors: 2,500 hours. (3) If your engine family has an alternate useful life under § 1048.101(g) that is shorter than the period specified in paragraph (a)(2)(ii) of this section, you may not schedule critical emission-related maintenance more frequently than the alternate useful life, except as specified in paragraph (c) of this section. (4) You may ask us to approve a maintenance interval shorter than that specified in paragraphs (a)(2) of this section. In your request you must describe the proposed maintenance step, recommend the maximum feasible interval for this maintenance, include your rationale with supporting evidence to support the need for the maintenance at the recommended interval, and demonstrate that the maintenance will be done at the recommended interval on in-use engines. In considering your request, we will evaluate the information you provide and any other available information to establish alternate specifications for maintenance intervals, if appropriate. (b) Recommended additional maintenance. (c) Special maintenance. (d) Noncritical emission-related maintenance. (e) Maintenance that is not emission-related. (f) Source of parts and repairs. (1) Provide a component or service without charge under the purchase agreement. (2) Get us to waive this prohibition in the public's interest by convincing us the engine will work properly only with the identified component or service. (g) Payment for scheduled maintenance. (1) Each affected component was not in general use on similar engines before January 1, 2004. (2) The primary function of each affected component is to reduce emissions. (3) The cost of the scheduled maintenance is more than 2 percent of the price of the engine. (4) Failure to perform the maintenance would not cause clear problems that would significantly degrade the engine's performance. (h) Owners manual. [70 FR 40468, July 13, 2005, as amended at 73 FR 59233, Oct. 8, 2008; 75 FR 23021, Apr. 30, 2010] § 1048.130 What installation instructions must I give to equipment manufacturers? (a) If you sell an engine for someone else to install in a piece of nonroad equipment, give the engine installer instructions for installing it consistent with the requirements of this part. Include all information necessary to ensure that an engine will be installed in its certified configuration. (b) Make sure these instructions have the following information: (1) Include the heading: “Emission-related installation instructions”. (2) State: “Failing to follow these instructions when installing a certified engine in a piece of nonroad equipment violates federal law (40 CFR 1068.105(b)), subject to fines or other penalties as described in the Clean Air Act.”. (3) Describe the instructions needed to properly install the exhaust system and any other components. Include instructions consistent with the requirements of § 1048.205(v). (4) Describe the steps needed to control evaporative emissions, as described in §§ 1048.105 and 1048.245. (5) Describe any necessary steps for installing the diagnostic system described in § 1048.110. (6) Describe any limits on the range of applications needed to ensure that the engine operates consistently with your application for certification. For example, if your engines are certified only for constant-speed operation, tell equipment manufacturers not to install the engines in variable-speed applications. Also, if you need to avoid sustained high-load operation to meet the field-testing emission standards we specify in § 1048.101(c) or to comply with the provisions of § 1048.101(d), describe how the equipment manufacturer must properly size the engines for a given application. (7) Describe any other instructions to make sure the installed engine will operate according to design specifications in your application for certification. This may include, for example, instructions for installing aftertreatment devices when installing the engines. (8) State: “If you install the engine in a way that makes the engine's emission control information label hard to read during normal engine maintenance, you must place a duplicate label on the equipment, as described in 40 CFR 1068.105.”. (c) You do not need installation instructions for engines you install in your own equipment. (d) Provide instructions in writing or in an equivalent format. For example, you may post instructions on a publicly available Web site for downloading or printing. If you do not provide the instructions in writing, explain in your application for certification how you will ensure that each installer is informed of the installation requirements. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40469, July 13, 2005] § 1048.135 How must I label and identify the engines I produce? (a) Assign each engine a unique identification number and permanently affix, engrave, or stamp it on the engine in a legible way. (b) At the time of manufacture, affix a permanent and legible label identifying each engine. The label must be— (1) Attached in one piece so it is not removable without being destroyed or defaced. (2) Secured to a part of the engine needed for normal operation and not normally requiring replacement. (3) Durable and readable for the engine's entire life. (4) Written in English. (c) The label must— (1) Include the heading “EMISSION CONTROL INFORMATION”. (2) Include your full corporate name and trademark. You may identify another company and use its trademark instead of yours if you comply with the provisions of § 1048.635. (3) Include EPA's standardized designation for the engine family (and subfamily, where applicable). (4) State the engine's displacement (in liters); however, you may omit this from the label if all the engines in the engine family have the same per-cylinder displacement and total displacement. (5) State the date of manufacture [DAY (optional), MONTH, and YEAR]; however, you may omit this from the label if you stamp, engrave, or otherwise permanently identify it elsewhere on the engine, in which case you must also describe in your application for certification where you will identify the date on the engine. (6) Identify the emission control system. Use terms and abbreviations as described in 40 CFR 1068.45. You may omit this information from the label if there is not enough room for it and you put it in the owners manual instead. (7) State: “THIS ENGINE IS CERTIFIED TO OPERATE ON [specify operating fuel or fuels].” (8) Identify any requirements for fuel and lubricants. You may omit this information from the label if there is not enough room for it and you put it in the owners manual instead. (9) List specifications and adjustments for engine tuneups; show the proper position for the transmission during tuneup and state which accessories should be operating. You may omit this information from the label if there is not enough room for it and you put it in the owners manual instead. (10) State the useful life for your engine family if it has a longer useful life under § 1048.101(g)(1) or a shortened useful life under § 1048.101(g)(2). (11) Identify the emission standards to which you have certified the engine (in g/kW-hr). (12) Include one of the following compliance statements: (i) For engines that may be used in nonroad or stationary equipment, state: “THIS ENGINE COMPLIES WITH U.S. EPA REGULATIONS FOR [MODEL YEAR] NONROAD AND STATIONARY ENGINES.” (ii) For engines that will be used only in nonroad equipment, state: “THIS ENGINE COMPLIES WITH U.S. EPA REGULATIONS FOR [MODEL YEAR] NONROAD ENGINES.” (iii) For engines that will be used only in stationary equipment, state: “THIS ENGINE COMPLIES WITH U.S. EPA REGULATIONS FOR [MODEL YEAR] STATIONARY ENGINES.” (13) Include any of the following additional statements for special situations if they apply to your engines: (i) If your engines are certified only for constant-speed operation, state: “USE IN CONSTANT-SPEED APPLICATIONS ONLY.” (ii) If your engines are certified only for variable-speed operation, state: “USE IN VARIABLE-SPEED APPLICATIONS ONLY.” (iii) If your engines are certified only for high-load engines, state: “THIS ENGINE IS NOT INTENDED FOR OPERATION AT LESS THAN 75 PERCENT OF FULL LOAD.” (iv) If you certify your engines under § 1048.101(d), and show in your application for certification that in-use engines will experience infrequent high-load operation, state: “THIS ENGINE IS NOT INTENDED FOR OPERATION AT MORE THAN PERCENT OF FULL LOAD.” Specify the appropriate percentage of full load based on the nature of the engine protection. You may add other statements to discourage operation in engine-protection modes. (v) If your engines are certified to the voluntary standards in § 1048.140, state: “BLUE SKY SERIES” and identify the standard to which you certify the engines. (d) You may add information to the emission control information label to identify other emission standards that the engine meets or does not meet (such as California standards). You may also add other information to ensure that the engine will be properly maintained and used. (e) You may ask us to approve modified labeling requirements in this part 1048 if you show that it is necessary or appropriate. We will approve your request if your alternate label is consistent with the requirements of this part. (f) If you obscure the engine label while installing the engine in the equipment such that the label cannot be read during normal maintenance, you must place a duplicate label on the equipment. If others install your engine in their equipment in a way that obscures the engine label, we require them to add a duplicate label on the equipment (see 40 CFR 1068.105); in that case, give them the number of duplicate labels they request and keep the following records for at least five years: (1) Written documentation of the request from the equipment manufacturer. (2) The number of duplicate labels you send for each engine family and the date you sent them. [70 FR 40469, July 13, 2005, as amended at 73 FR 59233, Oct. 8, 2008] § 1048.140 What are the provisions for certifying Blue Sky Series engines? This section defines voluntary standards for a recognized level of superior emission control for engines designated as “Blue Sky Series” engines. If you certify an engine family under this section, it is subject to all the requirements of this part as if these voluntary standards were mandatory. To receive a certificate of conformity as “Blue Sky Series,” you must certify to one of the sets of exhaust emission standards in the following table: Table 1 of § 1048.140—Standards for Blue Sky Series Engines (g/kW-hr) Standards for steady-state and transient test Standards for HC + NO X CO HC + NO X CO 0.80 4.4 1.10 6.6 0.60 4.4 0.84 6.6 0.40 4.4 0.56 6.6 0.20 4.4 0.28 6.6 0.10 4.4 0.14 6.6 [73 FR 59234, Oct. 8, 2008] § 1048.145 Are there interim provisions that apply only for a limited time? The interim provisions in this section apply instead of other provisions in this part. This section describes when these interim provisions expire. (a)-(f) [Reserved] (g) Small-volume provisions. [86 FR 34515, June 29, 2021] Subpart C—Certifying Engine Families § 1048.201 What are the general requirements for obtaining a certificate of conformity? (a) You must send us a separate application for a certificate of conformity for each engine family. A certificate of conformity is valid starting with the indicated effective date, but it is not valid for any production after December 31 of the model year for which it is issued. No certificate will be issued after December 31 of the model year. (b) The application must contain all the information required by this part and must not include false or incomplete statements or information (see § 1048.255). (c) We may ask you to include less information than we specify in this subpart, as long as you maintain all the information required by § 1048.250. (d) You must use good engineering judgment for all decisions related to your application (see 40 CFR 1068.5). (e) An authorized representative of your company must approve and sign the application. (f) See § 1048.255 for provisions describing how we will process your application. (g) We may require you to deliver your test engines to a facility we designate for our testing (see § 1048.235(c)). (h) For engines that become new after being placed into service, such as engines converted to nonroad use after being used in motor vehicles, we may specify alternate certification provisions consistent with the intent of this part. See [70 FR 40470, July 13, 2005, as amended at 73 FR 59234, Oct. 8, 2008; 75 FR 23022, Apr. 30, 2010] § 1048.205 What must I include in my application? This section specifies the information that must be in your application, unless we ask you to include less information under § 1048.201(c). We may require you to provide additional information to evaluate your application. (a) Describe the engine family's specifications and other basic parameters of the engine's design and emission controls. List the fuel types on which your engines are designed to operate (for example, gasoline and natural gas). List each distinguishable engine configuration in the engine family. (b) Explain how the emission control systems operate. Describe the evaporative emission controls, if applicable. Also describe in detail all system components for controlling exhaust emissions, including all auxiliary emission control devices (AECDs) and all fuel-system components you will install on any production or test engine. Identify the part number of each component you describe. For this paragraph (b), treat as separate AECDs any devices that modulate or activate differently from each other. Include sufficient detail to allow us to evaluate whether the AECDs are consistent with the defeat device prohibition of § 1048.115. (c) Explain how the engine diagnostic system works, describing especially the engine conditions (with the corresponding diagnostic trouble codes) that cause the malfunction-indicator light to go on. Propose what you consider to be extreme conditions under which the diagnostic system should disregard trouble codes, as described in § 1048.110. (d) Describe the engines you selected for testing and the reasons for selecting them. (e) Describe the test equipment and procedures that you used, including any special or alternate test procedures you used (see § 1048.501). (f) Describe how you operated the emission-data engine before testing, including the duty cycle and the number of engine operating hours used to stabilize emission levels. Explain why you selected the method of service accumulation. Describe any scheduled maintenance you did. (g) List the specifications of each test fuel to show that it falls within the required ranges we specify in 40 CFR part 1065, subpart H. (h) Identify the engine family's useful life. (i) Include the maintenance instructions you will give to the ultimate purchaser of each new nonroad engine (see § 1048.125). (j) Include the emission-related installation instructions you will provide if someone else installs your engines in a piece of nonroad equipment (see § 1048.130). (k) Identify each high-cost warranted part and show us how you calculated its replacement cost, including the estimated retail cost of the part, labor rates, and labor hours to diagnose and replace defective parts. (l) Describe your emission control information label (see § 1048.135). (m) Identify the emission standards to which you are certifying engines in the engine family. (n) Identify the engine family's deterioration factors and describe how you developed them (see § 1048.240). Present any emission test data you used for this. (o) State that you operated your emission-data engines as described in the application (including the test procedures, test parameters, and test fuels) to show you meet the requirements of this part. (p) Present emission data to show that you meet emission standards, as follows: (1) Present exhaust emission data for HC, NO X (2) If your engine family includes a volatile liquid fuel (and you do not use design-based certification under § 1048.245), present evaporative test data to show your vehicles meet the evaporative emission standards we specify in subpart B of this part. Show these figures before and after applying deterioration factors, where applicable. (q) State that all the engines in the engine family comply with the field-testing emission standards we specify in § 1048.101(c) for all normal operation and use when tested as specified in § 1048.515. Describe any relevant testing, engineering analysis, or other information in sufficient detail to support your statement. (r) For engines not subject to transient testing requirements in § 148.101(a), include information showing how your emission controls will function during normal in-use transient operation. For example, this might include the following: (1) Emission data from transient testing of engines using measurement systems designed for measuring in-use emissions. (2) Comparison of the engine design for controlling transient emissions with that from engines for which you have emission data over the transient duty cycle for certification. (3) Detailed descriptions of control algorithms and other design parameters for controlling transient emissions. (s) Report test results as follows: (1) Report all test results involving measurement of pollutants for which emission standards apply. Include test results from invalid tests or from any other tests, whether or not they were conducted according to the test procedures of subpart F of this part. We may ask you to send other information to confirm that your tests were valid under the requirements of this part and 40 CFR part 1065. (2) Report measured CO 2 2 4 2 4 (t) Describe all adjustable operating parameters (see § 1048.115(e)), including production tolerances. For any operating parameters that do not qualify as adjustable parameters, include a description supporting your conclusion (see 40 CFR 1068.50(c)). Include the following in your description of each adjustable parameter: (1) For practically adjustable parameters, include the nominal or recommended setting, the intended practically adjustable range, and the limits or stops used to establish adjustable ranges. State that the limits, stops, or other means of inhibiting adjustment are effective in preventing adjustment of parameters on in-use engines to settings outside your intended practically adjustable ranges and provide information to support this statement. (2) For programmable operating parameters, state that you have restricted access to electronic controls to prevent parameter adjustments on in-use engines that would allow operation outside the practically adjustable range. Describe how your engines are designed to prevent unauthorized adjustments. (u) Provide the information to read, record, and interpret all the information broadcast by an engine's onboard computers and electronic control units. State that, upon request, you will give us any hardware, software, or tools we would need to do this. If you broadcast a surrogate parameter for torque values, you must provide us what we need to convert these into torque units. You may reference any appropriate publicly released standards that define conventions for these messages and parameters. Format your information consistent with publicly released standards. (v) Confirm that your emission-related installation instructions specify how to ensure that sampling of exhaust emissions will be possible after engines are installed in equipment and placed in service. If this cannot be done by simply adding a 20-centimeter extension to the exhaust pipe, show how to sample exhaust emissions in a way that prevents diluting the exhaust sample with ambient air. (w) State whether your certification is intended to include engines used in stationary applications. Also state whether your certification is limited for certain engines. If this is the case, describe how you will prevent use of these engines in applications for which they are not certified. This applies for engines such as the following: (1) Constant-speed engines. (2) Variable-speed engines. (x) Unconditionally certify that all the engines in the engine family comply with the requirements of this part, other referenced parts of the CFR, and the Clean Air Act. (y) Include good-faith estimates of U.S.-directed production volumes. Include a justification for the estimated production volumes if they are substantially different than actual production volumes in earlier years for similar models. (z) Include other applicable information, such as information specified in this part or part 1068 of this chapter related to requests for exemptions. (aa) Name an agent for service located in the United States. Service on this agent constitutes service on you or any of your officers or employees for any action by EPA or otherwise by the United States related to the requirements of this part. [70 FR 40470, July 13, 2005, as amended at 73 FR 3613, Jan. 18, 2008; 73 FR 59234, Oct. 8, 2008; 74 FR 56510, Oct. 30, 2009; 88 FR 4665, Jan. 24, 2023] § 1048.210 May I get preliminary approval before I complete my application? If you send us information before you finish the application, we will review it and make any appropriate determinations, especially for questions related to engine family definitions, auxiliary emission-control devices, deterioration factors, testing for service accumulation, and maintenance. Decisions made under this section are considered to be preliminary approval, subject to final review and approval. We will generally not reverse a decision where we have given you preliminary approval, unless we find new information supporting a different decision. If you request preliminary approval related to the upcoming model year or the model year after that, we will make best-efforts to make the appropriate determinations as soon as practicable. We will generally not provide preliminary approval related to a future model year more than two years ahead of time. [70 FR 40472, July 13, 2005] § 1048.220 How do I amend the maintenance instructions in my application? You may amend your emission-related maintenance instructions after you submit your application for certification as long as the amended instructions remain consistent with the provisions of § 1048.125. You must send the Designated Compliance Officer a written request to amend your application for certification for an engine family if you want to change the emission-related maintenance instructions in a way that could affect emissions. In your request, describe the proposed changes to the maintenance instructions. If operators follow the original maintenance instructions rather than the newly specified maintenance, this does not allow you to disqualify those engines from in-use testing or deny a warranty claim. (a) If you are decreasing or eliminating any specified maintenance, you may distribute the new maintenance instructions to your customers 30 days after we receive your request, unless we disapprove your request. This would generally include replacing one maintenance step with another. We may approve a shorter time or waive this requirement. (b) If your requested change would not decrease the specified maintenance, you may distribute the new maintenance instructions anytime after you send your request. For example, this paragraph (b) would cover adding instructions to increase the frequency of a maintenance step for engines in severe-duty applications. (c) You need not request approval if you are making only minor corrections (such as correcting typographical mistakes), clarifying your maintenance instructions, or changing instructions for maintenance unrelated to emission control. We may ask you to send us copies of maintenance instructions revised under this paragraph (c). [70 FR 40472, July 13, 2005, as amended at 73 FR 59235, Oct. 8, 2008; 75 FR 23022, Apr. 30, 2010] § 1048.225 How do I amend my application for certification to include new or modified engine configurations? Before we issue you a certificate of conformity, you may amend your application to include new or modified engine configurations, subject to the provisions of this section. After we have issued your certificate of conformity, you may send us an amended application requesting that we include new or modified engine configurations within the scope of the certificate, subject to the provisions of this section. You must amend your application if any changes occur with respect to any information included in your application. (a) You must amend your application before you take any of the following actions: (1) Add an engine configuration to an engine family. In this case, the engine configuration added must be consistent with other engine configurations in the engine family with respect to the criteria listed in § 1048.230. (2) Change an engine configuration already included in an engine family in a way that may affect emissions, or change any of the components you described in your application for certification. This includes production and design changes that may affect emissions any time during the engine's lifetime. (b) To amend your application for certification, send the Designated Compliance Officer the following information: (1) Describe in detail the addition or change in the engine model or configuration you intend to make. (2) Include engineering evaluations or data showing that the amended engine family complies with all applicable requirements. You may do this by showing that the original emission-data engine is still appropriate for showing that the amended family complies with all applicable requirements. (3) If the original emission-data engine for the engine family is not appropriate to show compliance for the new or modified engine configuration, include new test data showing that the new or modified engine configuration meets the requirements of this part. (c) We may ask for more test data or engineering evaluations. You must give us these within 30 days after we request them. (d) For engine families already covered by a certificate of conformity, we will determine whether the existing certificate of conformity covers your newly added or modified engine. You may ask for a hearing if we deny your request (see § 1048.820). (e) For engine families already covered by a certificate of conformity, you may start producing the new or modified engine configuration anytime after you send us your amended application and before we make a decision under paragraph (d) of this section. However, if we determine that the affected engines do not meet applicable requirements, we will notify you to cease production of the engines and may require you to recall the engines at no expense to the owner. Choosing to produce engines under this paragraph (e) is deemed to be consent to recall all engines that we determine do not meet applicable emission standards or other requirements and to remedy the nonconformity at no expense to the owner. If you do not provide information required under paragraph (c) of this section within 30 days after we request it, you must stop producing the new or modified engines. [73 FR 59235, Oct. 8, 2008] § 1048.230 How do I select engine families? (a) For purposes of certification, divide your product line into families of engines that are expected to have similar emission characteristics throughout the useful life as described in this section. Your engine family is limited to a single model year. (b) Group engines in the same engine family if they are the same in all of the following aspects: (1) The combustion cycle. (2) The cooling system (water-cooled vs. air-cooled). (3) Configuration of the fuel system (for example, fuel-injected vs. carbureted gasoline engines). (4) Method of air aspiration. (5) The number, location, volume, and composition of catalytic converters. (6) The number, arrangement (such as in-line or vee configuration), and approximate bore diameter of cylinders. (c) You may subdivide a group of engines that is identical under paragraph (b) of this section into different engine families if you show the expected emission characteristics are different during the useful life. (d) In unusual circumstances, you may group engines that are not identical with respect to the things listed in paragraph (b) of this section in the same engine family if you show that their emission characteristics during the useful life will be similar. (e) You may create separate families for exhaust emissions and evaporative emissions. If we do this, list both families on the emission control information label. (f) Where necessary, you may divide an engine family into sub-families to meet different emission standards, as specified in § 1048.101(a)(2). For issues related to compliance and prohibited actions, we will generally apply decisions to the whole engine family. For engine labels and other administrative provisions, we may approve your request for separate treatment of sub-families. [70 FR 40473, July 13, 2005, as amended at 73 FR 59235, Oct. 8, 2008; 75 FR 23022, Apr. 30, 2010] § 1048.235 What emission testing must I perform for my application for a certificate of conformity? This section describes the emission testing you must perform to show compliance with the emission standards in §§ 1048.101(a) and (b) and 1048.105 during certification. See § 1048.205(q) regarding emission testing related to the field-testing standards. See § 1048.240 and 40 CFR part 1065, subpart E, regarding service accumulation before emission testing. (a) Test your emission-data engines using the procedures and equipment specified in subpart F of this part. (b) Select emission-data engines according to the following criteria: (1) Exhaust testing. (2) Evaporative testing. (c) We may measure emissions from any of your test engines or other engines from the engine family, as follows: (1) We may decide to do the testing at your plant or any other facility. If we do this, you must deliver the test engine to a test facility we designate. The test engine you provide must include appropriate manifolds, aftertreatment devices, electronic control units, and other emission-related components not normally attached directly to the engine block. If we do the testing at your plant, you must schedule it as soon as possible and make available the instruments, personnel, and equipment we need. (2) If we measure emissions on one of your test engines, the results of that testing become the official emission results for the engine. Unless we later invalidate these data, we may decide not to consider your data in determining if your engine family meets applicable requirements. (3) Before we test one of your engines, we may set its adjustable parameters to any point within the physically adjustable ranges (see § 1048.115(e)). (4) Before we test one of your engines, we may calibrate it within normal production tolerances for anything we do not consider an adjustable parameter. For example, this would apply where we determine that an engine parameter is not an adjustable parameter (as defined in § 1048.801) but that it is subject to production variability. (d) You may ask to use carryover emission data from a previous model year instead of doing new tests, but only if all the following are true: (1) The engine family from the previous model year differs from the current engine family only with respect to model year or other characteristics unrelated to emissions. You may also ask to add a configuration subject to § 1048.225. (2) The emission-data engine from the previous model year remains the appropriate emission-data engine under paragraph (b) of this section. (3) The data show that the emission-data engine would meet all the requirements that apply to the engine family covered by the application for certification. (e) We may require you to test another engine of the same or different configuration in addition to the engine tested under paragraph (b) of this section. (f) If you use an alternate test procedure under 40 CFR 1065.10 and later testing shows that such testing does not produce results that are equivalent to the procedures specified in subpart F of this part, we may reject data you generated using the alternate procedure. (g) Measure CO 2 4 2 2 4 (1) Round CO 2 (2) Round N 2 (3) Round CH 4 [70 FR 40473, July 13, 2005, as amended at 73 FR 59235, Oct. 8, 2008; 74 FR 56510, Oct. 30, 2009] § 1048.240 How do I demonstrate that my engine family complies with exhaust emission standards? (a) For purposes of certification, your engine family is considered in compliance with the applicable numerical emission standards in § 1048.101(a) and (b) if all emission-data engines representing that family have test results showing official emission results and deteriorated emission levels at or below these standards. This includes all test points over the course of the durability demonstration. This also applies for all test points for emission-data engines within the family used to establish deterioration factors. See (b) Your engine family is deemed not to comply if any emission-data engine representing that family has test results showing an official emission result or a deteriorated emission level for any pollutant that is above an applicable emission standard from § 1048.101(a) and (b). Similarly, your engine family is deemed not to comply if any emission-data engine representing that family has test results showing any emission level above the applicable field-testing standard for any pollutant. This also applies for all test points for emission-data engines within the family used to establish deterioration factors. (c) To compare emission levels from the emission-data engine with the applicable emission standards, apply deterioration factors to the measured emission levels for each pollutant. Specify the deterioration factors based on emission measurements using four significant figures, consistent with good engineering judgment. For example, your deterioration factors must take into account any available data from in-use testing with similar engines (see subpart E of this part). Small-volume engine manufacturers may use assigned deterioration factors that we establish. In addition, anyone may use assigned deterioration factors for engine families with a projected U.S.-directed production volume at or below 300 engines. Apply deterioration factors as follows: (1) Multiplicative deterioration factor. (2) Additive deterioration factor. X (d) Collect emission data using measurements to one more decimal place than the applicable standard. Apply the deterioration factor to the official emission result, as described in paragraph (c) of this section, then round the adjusted figure to the same number of decimal places as the emission standard. Compare the rounded emission levels to the emission standard for each emission-data engine. In the case of HC + NO X (e) Use good engineering judgment to demonstrate compliance with field-testing standards throughout the useful life. You may, but are not required to, apply the same deterioration factors used to show compliance with the applicable duty-cycle standards. (f) You may alternatively determine and verify deterioration factors based on bench-aged aftertreatment as described in 40 CFR 1036.245 and 1036.246, with the following exceptions: (1) The minimum required aging for engines as specified in 40 CFR 1036.245(c)(2) is 300 hours. Operate the engine for service accumulation using the same sequence of duty cycles that would apply for determining a deterioration factor under paragraph (c) of this section. (2) Use good engineering judgment to perform verification testing using the procedures of § 1048.515 rather than 40 CFR 1036.555. For PEMS testing, measure emissions as the equipment goes through its normal operation over the course of the day (or shift-day). [70 FR 40474, July 13, 2005, as amended at 73 FR 59236, Oct. 8, 2008; 75 FR 23022, Apr. 30, 2010; 88 FR 4665, Jan. 24, 2023] § 1048.245 How do I demonstrate that my engine family complies with evaporative emission standards? (a) For certification, your engine family is considered in compliance with the evaporative emission standards in subpart B of this part if you do either of the following: (1) You have test results showing that evaporative emissions in the family are at or below the standards throughout the useful life. (2) Where applicable, you comply with the design specifications in paragraph (e) of this section. (b) Your engine family does not comply if any fuel system representing that family has test results showing emission levels above the standards. (c) Use good engineering judgment to develop a test plan to establish deterioration factors to show how much emissions increase at the end of the useful life. (d) If you adjust the emission levels for deterioration, round them to the same number of decimal places as the emission standard. Compare the rounded emission levels to the emission standard for each test fuel system. (e) You may demonstrate that your engine family complies with the evaporative emission standards by demonstrating that you use the following control technologies: (1) For certification to the standards specified in § 1048.105(c), with the following technologies: (i) Use a tethered or self-closing gas cap on a fuel tank that stays sealed up to a positive pressure of 24.5 kPa (3.5 psig); however, they may contain air inlets that open when there is a vacuum pressure inside the tank. Nonmetal fuel tanks must also use one of the qualifying designs for controlling permeation emissions specified in 40 CFR 1060.240. (ii) [Reserved] (2) For certification to the standards specified in § 1048.105(d), demonstrating that you use design features to prevent fuel boiling under all normal operation. If you install engines in equipment, you may do this using fuel temperature data measured during normal operation. Otherwise, you may do this by including appropriate information in your emission-related installation instructions. (3) We may establish additional options for design-based certification where we find that new test data demonstrate that a technology will ensure compliance with the emission standards in this section. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40474, July 13, 2005; 73 FR 59236, Oct. 8, 2008; 75 FR 23022, Apr. 30, 2010] § 1048.250 What records must I keep and make available to EPA? (a) Send the Designated Compliance Officer information related to your U.S.-directed production volumes as described in § 1048.345. In addition, within 45 days after the end of the model year, you must send us a report describing information about engines you produced during the model year as follows: (1) State the total production volume for each engine family that is not subject to reporting under § 1048.345. (2) State the total production volume for any engine family for which you produce engines after completing the reports required in § 1048.345. (3) For production volumes you report under this paragraph (a), identify whether or not the figures include California sales. Include a separate count of production volumes for California sales if those figures are available. (b) Organize and maintain the following records: (1) A copy of all applications and any summary information you send us. (2) Any of the information we specify in § 1048.205 that you were not required to include in your application. (3) A detailed history of each emission-data engine. For each engine, describe all of the following: (i) The emission-data engine's construction, including its origin and buildup, steps you took to ensure that it represents production engines, any components you built specially for it, and all the components you include in your application for certification. (ii) How you accumulated engine operating hours (service accumulation), including the dates and the number of hours accumulated. (iii) All maintenance, including modifications, parts changes, and other service, and the dates and reasons for the maintenance. (iv) All your emission tests, including documentation on routine and standard tests, as specified in part 40 CFR part 1065, and the date and purpose of each test. (v) All tests to diagnose engine or emission-control performance, giving the date and time of each and the reasons for the test. (vi) Any other significant events. (4) Production figures for each engine family divided by assembly plant. (5) Keep a list of engine identification numbers for all the engines you produce under each certificate of conformity. (c) Keep data from routine emission tests (such as test cell temperatures and relative humidity readings) for one year after we issue the associated certificate of conformity. Keep all other information specified in this section for eight years after we issue your certificate. (d) Store these records in any format and on any media, as long as you can promptly send us organized, written records in English if we ask for them. You must keep these records readily available. We may review them at any time. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40474, July 13, 2005; 73 FR 59236, Oct. 8, 2008] § 1048.255 What decisions may EPA make regarding a certificate of conformity? (a) If we determine an application is complete and shows that the engine family meets all the requirements of this part and the Act, we will issue a certificate of conformity for the engine family for that model year. We may make the approval subject to additional conditions. (b) We may deny an application for certification if we determine that an engine family fails to comply with emission standards or other requirements of this part or the Clean Air Act. We will base our decision on all available information. If we deny an application, we will explain why in writing. (c) In addition, we may deny your application or suspend or revoke a certificate of conformity if you do any of the following: (1) Refuse to comply with any testing or reporting requirements in this part. (2) Submit false or incomplete information. This includes doing anything after submitting an application that causes submitted information to be false or incomplete. (3) Cause any test data to become inaccurate. (4) Deny us from completing authorized activities (see 40 CFR 1068.20). This includes a failure to provide reasonable assistance. (5) Produce engines for importation into the United States at a location where local law prohibits us from carrying out authorized activities. (6) Fail to supply requested information or amend an application to include all engines being produced. (7) Take any action that otherwise circumvents the intent of the Act or this part. (d) We may void a certificate of conformity if you fail to keep records, send reports, or give us information as required under this part or the Act. Note that these are also violations of 40 CFR 1068.101(a)(2). (e) We may void a certificate of conformity if we find that you intentionally submitted false or incomplete information. This includes doing anything after submitting an application that causes submitted information to be false or incomplete after submission. (f) If we deny an application or suspend, revoke, or void a certificate, you may ask for a hearing (see § 1048.820). [86 FR 34515, June 29, 2021] Subpart D—Testing Production-line Engines § 1048.301 When must I test my production-line engines? (a) If you produce engines that are subject to the requirements of this part, you must test them as described in this subpart, except as follows: (1) [Reserved] (2) We may exempt engine families with a projected U.S.-directed production volume below 150 units from routine testing under this subpart. Request this exemption in your application for certification and include your basis for projecting a production volume below 150 units. We will approve your request if we agree that you have made good-faith estimates of your production volumes. Your exemption is approved when we grant your certificate. You must promptly notify us if your actual production exceeds 150 units during the model year. If you exceed the production limit or if there is evidence of a nonconformity, we may require you to test production-line engines under this subpart, or under 40 CFR part 1068, subpart E, even if we have approved an exemption under this paragraph (a)(2). (b) We may suspend or revoke your certificate of conformity for certain engine families if your production-line engines do not meet the requirements of this part or you do not fulfill your obligations under this subpart (see §§ 1048.325 and 1048.340). (c) Other regulatory provisions authorize us to suspend, revoke, or void your certificate of conformity, or order recalls for engine families, without regard to whether they have passed these production-line testing requirements. The requirements of this subpart do not affect our ability to do selective enforcement audits, as described in part 1068 of this chapter. Individual engines in families that pass these production-line testing requirements must also conform to all applicable regulations of this part and part 1068 of this chapter. (d) You may use alternate programs for testing production-line engines in the following circumstances: (1) You may use analyzers and sampling systems that meet the field-testing requirements of 40 CFR part 1065, subpart J, but not the otherwise applicable requirements in 40 CFR part 1065 for laboratory testing, to demonstrate compliance with duty-cycle emission standards if you double the minimum sampling rate specified in § 1048.310(b). Use measured test results to determine whether engines comply with applicable standards without applying a measurement allowance. This alternate program does not require prior approval but we may disallow use of this option where we determine that use of field-grade equipment would prevent you from being able to demonstrate that your engines are being produced to conform to the specifications in your application for certification. (2) You may ask to use another alternate program for testing production-line engines. In your request, you must show us that the alternate program gives equal assurance that your products meet the requirements of this part. We may waive some or all of this subpart's requirements if we approve your alternate approach. For example, in certain circumstances you may be able to give us equal assurance that your products meet the requirements of this part by using less rigorous measurement methods if you offset that by increasing the number of test engines. (e) If you certify an engine family with carryover emission data, as described in § 1048.235(d), and these equivalent engine families consistently pass the production-line testing requirements over the preceding two-year period, you may ask for a reduced testing rate for further production-line testing for that family. The minimum testing rate is one engine per engine family. If we reduce your testing rate, we may limit our approval to any number of model years. In determining whether to approve your request, we may consider the number of engines that have failed the emission tests. (f) We may ask you to make a reasonable number of production-line engines available for a reasonable time so we can test or inspect them for compliance with the requirements of this part. [73 FR 59236, Oct. 8, 2008] § 1048.305 How must I prepare and test my production-line engines? This section describes how to prepare and test production-line engines. You must assemble the test engine in a way that represents the assembly procedures for other engines in the engine family. You must ask us to approve any deviations from your normal assembly procedures for other production engines in the engine family. (a) Test procedures. (b) Modifying a test engine. (1) You document the need for doing so in your procedures for assembling and inspecting all your production engines and make the action routine for all the engines in the engine family. (2) This subpart otherwise specifically allows your action. (3) We approve your action in advance. (c) Engine malfunction. (d) Setting adjustable parameters. (1) We may require you to adjust idle speed outside the physically adjustable range as needed, but only until the engine has stabilized emission levels (see paragraph (e) of this section). We may ask you for information needed to establish an alternate minimum idle speed. (2) We may specify adjustments within the physically adjustable range by considering their effect on emission levels. We may also consider how likely it is that someone will make such an adjustment with in-use equipment. (e) Stabilizing emission levels. (1) 50 hours. (2) The number of hours you operated your emission-data engine for certifying the engine family (see 40 CFR part 1065, subpart E). (f) Damage during shipment. (g) Retesting after invalid tests. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40475, July 13, 2005; 73 FR 59237, Oct. 8, 2008] § 1048.310 How must I select engines for production-line testing? (a) Use test results from two engines each quarter to calculate the required sample size for the model year for each engine family. (b) Early in each calendar quarter, randomly select and test two engines from the end of the assembly line for each engine family. (c) Calculate the required sample size for each engine family. Separately calculate this figure for HC + NO X Where: N = Required sample size for the model year. t 95 σ = Test sample standard deviation (see paragraph (c)(2) of this section). x = Mean of emission test results of the sample. STD = Emission standard. (1) Determine the 95% confidence coefficient, t 95 n t 95 n t 95 n t 95 2 6.31 12 1.80 22 1.72 3 2.92 13 1.78 23 1.72 4 2.35 14 1.77 24 1.71 5 2.13 15 1.76 25 1.71 6 2.02 16 1.75 26 1.71 7 1.94 17 1.75 27 1.71 8 1.90 18 1.74 28 1.70 9 1.86 19 1.73 29 1.70 10 1.83 20 1.73 30 + 1.70 11 1.81 21 1.72 (2) Calculate the standard deviation, σ, for the test sample using the following formula: Where: X i n = The number of tests completed in an engine family. (d) Use final deteriorated test results to calculate the variables in the equations in paragraph (c) of this section (see § 1048.315(a)). (e) After each new test, recalculate the required sample size using the updated mean values, standard deviations, and the appropriate 95-percent confidence coefficient. (f) Distribute the remaining tests evenly throughout the rest of the year. You may need to adjust your schedule for selecting engines if the required sample size changes. If your scheduled quarterly testing for the remainder of the model year is sufficient to meet the calculated sample size, you may wait until the next quarter to do additional testing. Continue to randomly select engines from each engine family. (g) Continue testing until one of the following things happens: (1) After completing the minimum number of tests required in paragraph (b) of this section, the number of tests completed in an engine family, n, is greater than the required sample size, N, and the sample mean, x, is less than or equal to the emission standard. For example, if N = 5.1 after the fifth test, the sample-size calculation does not allow you to stop testing. (2) The engine family does not comply according to § 1048.315. (3) You test 30 engines from the engine family. (4) You test one percent of your projected annual U.S.-directed production volume for the engine family, rounded to the nearest whole number. Do not count an engine under this paragraph (g)(4) if it fails to meet an applicable emission standard. You may stop testing after you test one percent of your production volume even if you have not tested the number of engines specified in paragraph (b) of this section. For example, if projected volume is 475 engines, test two engines in each of the first two quarters and one engine in the third quarter to fulfill your testing requirements under this section for that engine family. (5) You choose to declare that the engine family does not comply with the requirements of this subpart. (h) If the sample-size calculation allows you to stop testing for one pollutant but not another, you must continue measuring emission levels of all pollutants for any additional tests required under this section. However, you need not continue making the calculations specified in this subpart for the pollutant for which testing is not required. This paragraph (h) does not affect the number of tests required under this section, the required calculations in § 1048.315, or the remedial steps required under § 1048.320. (i) You may elect to test more randomly chosen engines than we require under this section. Include these engines in the sample-size calculations. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40475, July 13, 2005; 73 FR 59237, Oct. 8, 2008] § 1048.315 How do I know when my engine family fails the production-line testing requirements? This section describes the pass/fail criteria for the production-line testing requirements. We apply these criteria on an engine-family basis. See § 1048.320 for the requirements that apply to individual engines that fail a production-line test. (a) Calculate your test results as follows: (1) Initial and final test results. (2) Final deteriorated test results. (3) Round deteriorated test results. (b) Construct the following CumSum Equation for each engine family for HC + NO X C i i-1 i Where: C i C i i.e. 1 X i STD = Emission standard. (c) Use final deteriorated test results to calculate the variables in the equation in paragraph (b) of this section (see § 1048.315(a)). (d) After each new test, recalculate the CumSum statistic. (e) If you test more than the required number of engines, include the results from these additional tests in the CumSum Equation. (f) After each test, compare the current CumSum statistic, C i (g) If the CumSum statistic exceeds the Action Limit in two consecutive tests, the engine family fails the production-line testing requirements of this subpart. Tell us within ten working days if this happens. (h) If you amend the application for certification for an engine family (see § 1048.225), do not change any previous calculations of sample size or CumSum statistics for the model year. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40475, July 13, 2005; 73 FR 59238, Oct. 8, 2008] § 1048.320 What happens if one of my production-line engines fails to meet emission standards? If you have a production-line engine with final deteriorated test results exceeding one or more emission standards (see § 1048.315(a)), the certificate of conformity is automatically suspended for that failing engine. You must take the following actions before your certificate of conformity can cover that engine: (a) Correct the problem and retest the engine to show it complies with all emission standards. (b) Include the test results and describe the remedy for each engine in the written report required under § 1048.345. [67 FR 68347, Nov. 8, 2002, as amended at 73 FR 59238, Oct. 8, 2008] § 1048.325 What happens if an engine family fails the production-line testing requirements? (a) We may suspend your certificate of conformity for an engine family if it fails under § 1048.315. The suspension may apply to all facilities producing engines from an engine family, even if you find noncompliant engines only at one facility. (b) We will tell you in writing if we suspend your certificate in whole or in part. We will not suspend a certificate until at least 15 days after the engine family fails. The suspension is effective when you receive our notice. (c) Up to 15 days after we suspend the certificate for an engine family, you may ask for a hearing (see § 1048.820). If we agree before a hearing occurs that we used erroneous information in deciding to suspend the certificate, we will reinstate the certificate. (d) Section 1048.335 specifies steps you must take to remedy the cause of the engine family's production-line failure. All the engines you have produced since the end of the last test period are presumed noncompliant and should be addressed in your proposed remedy. We may require you to apply the remedy to engines produced earlier if we determine that the cause of the failure is likely to have affected the earlier engines. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40475, July 13, 2005; 73 FR 59238, Oct. 8, 2008] § 1048.330 May I sell engines from an engine family with a suspended certificate of conformity? You may sell engines that you produce after we suspend the engine family's certificate of conformity under § 1048.315 only if one of the following occurs: (a) You test each engine you produce and show it complies with emission standards that apply. (b) We conditionally reinstate the certificate for the engine family. We may do so if you agree to recall all the affected engines and remedy any noncompliance at no expense to the owner if later testing shows that the engine family still does not comply. § 1048.335 How do I ask EPA to reinstate my suspended certificate? (a) Send us a written report asking us to reinstate your suspended certificate. In your report, identify the reason for noncompliance, propose a remedy for the engine family, and commit to a date for carrying it out. In your proposed remedy include any quality control measures you propose to keep the problem from happening again. (b) Give us data from production-line testing that shows the remedied engine family complies with all the emission standards that apply. § 1048.340 When may EPA revoke my certificate under this subpart and how may I sell these engines again? (a) We may revoke your certificate for an engine family in the following cases: (1) You do not meet the reporting requirements. (2) Your engine family fails to comply with the requirements of this subpart and your proposed remedy to address a suspended certificate under § 1048.325 is inadequate to solve the problem or requires you to change the engine's design or emission-control system. (b) To sell engines from an engine family with a revoked certificate of conformity, you must modify the engine family and then show it complies with the requirements of this part. (1) If we determine your proposed design change may not control emissions for the engine's full useful life, we will tell you within five working days after receiving your report. In this case we will decide whether production-line testing will be enough for us to evaluate the change or whether you need to do more testing. (2) Unless we require more testing, you may show compliance by testing production-line engines as described in this subpart. (3) We will issue a new or updated certificate of conformity when you have met these requirements. § 1048.345 What production-line testing records must I send to EPA? (a) Within 30 calendar days of the end of each calendar quarter, send us a report with the following information: (1) Describe any facility used to test production-line engines and state its location. (2) State the total U.S.-directed production volume and number of tests for each engine family. (3) Describe how you randomly selected engines. (4) Describe each test engine, including the engine family's identification and the engine's model year, build date, model number, identification number, and number of hours of operation before testing. (5) Identify how you accumulated hours of operation on the engines and describe the procedure and schedule you used. (6) Provide the test number; the date, time and duration of testing; test procedure; all initial test results; final test results; and final deteriorated test results for all tests. Provide the emission results for all measured pollutants. Include information for both valid and invalid tests and the reason for any invalidation. (7) Describe completely and justify any nonroutine adjustment, modification, repair, preparation, maintenance, or test for the test engine if you did not report it separately under this subpart. Include the results of any emission measurements, regardless of the procedure or type of equipment. (8) Provide the CumSum analysis required in § 1048.315 and the sample-size calculation required in § 1048.310 for each engine family. (9) Report on each failed engine as described in § 1048.320. (10) State the date the calendar quarter ended for each engine family. (b) We may ask you to add information to your written report, so we can determine whether your new engines conform with the requirements of this subpart. We may also ask you to send less information. (c) An authorized representative of your company must sign the following statement: We submit this report under Sections 208 and 213 of the Clean Air Act. Our production-line testing conformed completely with the requirements of 40 CFR part 1048. We have not changed production processes or quality-control procedures for test engines in a way that might affect emission controls. All the information in this report is true and accurate, to the best of my knowledge. I know of the penalties for violating the Clean Air Act and the regulations. (Authorized Company Representative) (d) Send electronic reports of production-line testing to the Designated Compliance Officer using an approved information format. If you want to use a different format, send us a written request with justification for a waiver. (e) We will send copies of your reports to anyone from the public who asks for them. See § 1048.815 for information on how we treat information you consider confidential. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40476, July 13, 2005; 73 FR 59238, Oct. 8, 2008] § 1048.350 What records must I keep? (a) Organize and maintain your records as described in this section. We may review your records at any time. (b) Keep paper or electronic records of your production-line testing for eight years after you complete all the testing required for an engine family in a model year. (c) Keep a copy of the written reports described in § 1048.345. (d) Keep the following additional records: (1) A description of all test equipment for each test cell that you can use to test production-line engines. (2) The names of supervisors involved in each test. (3) The name of anyone who authorizes adjusting, repairing, preparing, or modifying a test engine and the names of all supervisors who oversee this work. (4) If you shipped the engine for testing, the date you shipped it, the associated storage or port facility, and the date the engine arrived at the testing facility. (5) Any records related to your production-line tests that are not in the written report. (6) A brief description of any significant events during testing not otherwise described in the written report or in this section. (7) Any information specified in § 1048.345 that you do not include in your written reports. (e) If we ask, you must give us projected or actual production figures for an engine family. We may ask you to divide your production figures by maximum engine power, displacement, fuel type, or assembly plant (if you produce engines at more than one plant). (f) Keep records of the engine identification number for each engine you produce under each certificate of conformity. You may identify these numbers as a range. Give us these records within 30 days if we ask for them. (g) We may ask you to keep or send other information necessary to implement this subpart. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40476, July 13, 2005; 73 FR 59239, Oct. 8, 2008] Subpart E—Testing In-use Engines § 1048.401 What testing requirements apply to my engines that have gone into service? (a) If you produce engines that are subject to the requirements of this part, you must test them as described in this subpart. This generally involves testing engines in the field or removing them for measurement in a laboratory. (b) We may approve an alternate plan for showing that in-use engines comply with the requirements of this part if one of the following is true: (1) You produce 200 or fewer engines per year in the selected engine family. (2) Removing the engine from most of the applications for that engine family causes significant, irreparable damage to the equipment. (3) You identify a unique aspect of your engine applications that keeps you from doing the required in-use testing. (c) We may void your certificate of conformity for an engine family if you do not meet your obligations under this part. (d) Independent of your responsibility to test in-use engines, we may choose at any time to do our own testing of your in-use engines. (e) If in-use testing shows that engines fail to meet emission standards or other requirements of this part, we may pursue a recall or other remedy as allowed by the Act (see § 1048.415). § 1048.405 How does this program work? (a) You must test in-use engines, for exhaust emissions, from the families we select. We may select up to 25 percent of your engine families in any model year—or one engine family if you have three or fewer families. We will select engine families for testing before the end of the model year. When we select an engine family for testing, we may specify that you preferentially test engines based on fuel type or equipment type. In addition, we may identify specific modes of operation or sampling times. You may choose to test additional engine families that we do not select. (b) Send us an in-use testing plan within six months after we direct you to test a particular engine family. If we request additional information or require you to modify your plan to meet the requirements of this subpart, you must provide the information or the modified plan within 30 days of our request. Complete the testing within 36 months after we direct you to test a particular engine family. (c) You may need to test engines from more than one model year at a given time. (d) In appropriate extreme and unusual circumstances that are clearly outside your control and could not have been avoided by the exercise of prudence, diligence, and due care, we may allow more time to complete testing or we may waive the in-use testing requirement for an engine family. For example, if your test fleet is destroyed by severe weather during service accumulation and we agree that completion of testing is not possible, we would generally waive testing requirements for that engine family. [67 FR 68347, Nov. 8, 2002, as amended at 73 FR 59239, Oct. 8, 2008; 75 FR 23022, Apr. 30, 2010] § 1048.410 How must I select, prepare, and test my in-use engines? (a) You may make arrangements to select representative test engines from your own fleet or from other independent sources. (b) For the selected engine families, select engines that you or your customers have— (1) Operated for at least 50 percent of the engine family's useful life (see § 1048.101(d)); (2) Not maintained or used in an abnormal way; and (3) Documented in terms of total hours of operation, maintenance, operating conditions, and storage. (c) Use the following methods to determine the number of engines you must test in each engine family: (1) Test at least two engines if you produce 2,000 or fewer engines in the model year from all engine families, or if you produce 500 or fewer engines from the selected engine family. Otherwise, test at least four engines. (2) If you successfully complete an in-use test program on an engine family and later certify an equivalent engine family with carryover emission data, as described in § 1048.235(c), then test at least one engine instead of the testing rates in paragraph (c)(1) of this section. (3) If you test the minimum required number of engines and all comply fully with emission standards, you may stop testing. (4) For each engine that fails any applicable standard, test two more. Regardless of measured emission levels, you do not have to test more than ten engines in an engine family. You may do more tests than we require. (5) You may concede that the engine family does not comply before testing a total of ten engines. (d) You may do minimal maintenance to set components of a test engine to specifications for anything we do not consider an adjustable parameter (see § 1048.205(p)). Limit maintenance to what is in the owner's instructions for engines with that amount of service and age. Document all maintenance and adjustments. (e) You may do repeat measurements with a test engine; however, you must conduct the same number of tests on each engine. (f) For a test program on an engine family, choose one of the following methods to test your engines: (1) Remove the selected engines for testing in a laboratory. Use the applicable steady-state and transient procedures in subpart F of this part to show compliance with the duty-cycle standards in § 1048.101(a) and (b). We may direct you to measure emissions on the dynamometer using the supplemental test procedures in § 1048.515 to show compliance with the field-testing standards in § 1048.101(c). (2) Test the selected engines while they remain installed in the equipment. Use the field testing procedures in subpart F of this part. Measure emissions during normal operation of the equipment to show compliance with the field-testing standards in § 1048.101(c). We may direct you to include specific areas of normal operation. (g) You may ask us to waive parts of the prescribed test procedures if they are not necessary to determine in-use compliance. (h) Calculate the average emission levels for an engine family from the results for the set of tested engines. Round them to the number of decimal places in the emission standards expressed to one more decimal place. [67 FR 68347, Nov. 8, 2002, as amended at 73 FR 59239, Oct. 8, 2008] § 1048.415 What happens if in-use engines do not meet requirements? (a) Determine the reason each in-use engine exceeds the emission standards. (b) If the average emission levels calculated in § 1048.410(h) exceed any of the emission standards that apply, notify us within fifteen days of completing testing on this family. Otherwise follow the reporting instructions in § 1048.420. (c) We will consider failure rates, average emission levels, and any defects—among other things—to decide on taking remedial action under this subpart (see 40 CFR 1068.505). We may consider the results from any voluntary additional testing you perform. We may also consider information related to testing from other engine families showing that you designed them to exceed the minimum requirements for controlling emissions. We may order a recall before or after you complete testing of an engine family if we determine a substantial number of engines do not conform to section 213 of the Act or to this part. The scope of the recall may include other engine families in the same or different model years if the cause of the problem identified in paragraph (a) of this section applies more broadly than the tested engine family, as allowed by the Act. (d) If in-use testing reveals a design or manufacturing defect that prevents engines from meeting the requirements of this part, you must correct the defect as soon as possible for any future production for engines in every family affected by the defect. See 40 CFR 1068.501 for additional requirements related to defect reporting. (e) You may voluntarily recall an engine family for emission failures, as described in 40 CFR 1068.535, unless we have ordered a recall for that family under 40 CFR 1068.505. (f) You have the right to a hearing before we order you to recall your engines or implement an alternative remedy (see § 1048.820). [67 FR 68347, Nov. 8, 2002, as amended at 73 FR 59239, Oct. 8, 2008] § 1048.420 What in-use testing information must I report to EPA? (a) In a report to us within three months after you finish testing an engine family, do all the following: (1) Identify the engine family, model, serial number, and date of manufacture. (2) For each engine inspected or considered for testing, identify whether the diagnostic system was functioning. (3) Describe the specific reasons for disqualifying any engines for not being properly maintained or used. (4) For each engine selected for testing, include the following information: (i) Estimate the hours each engine was used before testing. (ii) Describe all maintenance, adjustments, modifications, and repairs to each test engine. (5) State the date and time of each test attempt. (6) Include the results of all emission testing, including incomplete or invalidated tests, if any. (b) Send electronic reports of in-use testing to the Designated Compliance Officer using an approved information format. If you want to use a different format, send us a written request with justification for a waiver. (c) We will send copies of your reports to anyone from the public who asks for them. See § 1048.815 for information on how we treat information you consider confidential. (d) We may ask for more information. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40476, July 13, 2005] § 1048.425 What records must I keep? (a) Organize and maintain your records as described in this section. We may review your records at any time. (b) Keep paper records of your in-use testing for one full year after you complete all the testing required for an engine family in a model year. You may use any additional storage formats or media if you like. (c) Keep a copy of the written reports described in § 1048.420. (d) Keep any additional records related to the procurement process. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40476, July 13, 2005] Subpart F—Test Procedures § 1048.501 How do I run a valid emission test? (a) Use the equipment and procedures for spark-ignition engines in 40 CFR part 1065 to determine whether engines meet the duty-cycle emission standards in § 1048.101(a) and (b). Measure the emissions of all the pollutants we regulate in § 1048.101 using the sampling procedures specified in 40 CFR part 1065. Measure CO 2 2 4 (b) Section 1048.515 describes the supplemental procedures for evaluating whether engines meet the field-testing emission standards in § 1048.101(c). (c) Use the fuels and lubricants specified in 40 CFR part 1065, subpart H, to perform valid tests for all the testing we require in this part, except as noted in § 1048.515. (1) Use gasoline meeting the specifications described in 40 CFR 1065.710(c) for general testing. For service accumulation, use the test fuel or any commercially available fuel that is representative of the fuel that in-use engines will use. (2) You may alternatively use ethanol-blended fuel meeting the specifications described in 40 CFR 1065.710(b) for general testing without our advance approval. If you use the ethanol-blended fuel for certifying a given engine family, you may also use it for production-line testing or any other testing you perform for that engine family under this part. If you use the ethanol-blended fuel for certifying a given engine family, we may use the ethanol-blended fuel or the specified neat gasoline test fuel with that engine family. (d) In place of the provisions of 40 CFR 1065.405, you may consider emission levels stable without measurement after 50 hours of engine operation. (e) To test engines for evaporative emissions, use the equipment and procedures specified for testing diurnal emissions as described in 40 CFR 1060.525, subject to the following provisions: (1) Precondition nonmetal fuel tanks as specified in 40 CFR 1060.520(a) and (b). (2) For engines equipped with carbon canisters that store fuel vapors that will be purged for combustion in the engine, precondition the canister as specified in 40 CFR 86.132-96(h) and then operate the engine for 60 minutes over repeat runs of the duty cycle specified in appendix II of this part. (3) Start the diurnal emission test after the engine is stabilized at room temperatures, but within 36 hours after the engine operation specified in paragraph (e)(2) of this section. (4) You may not separately measure permeation emissions from nonmetal fuel tanks for subtracting from the diurnal emission measurement. (5) Note that you may omit testing for evaporative emissions during certification if you certify by design, as specified in § 1048.245. (f) You may use special or alternate procedures to the extent we allow them under 40 CFR 1065.10. (g) This subpart is addressed to you as a manufacturer, but it applies equally to anyone who does testing for you, and to us when we perform testing to determine if your engines meet emission standards. [70 FR 40476, July 13, 2005, as amended at 73 FR 59239, Oct. 8, 2008; 74 FR 56510, Oct. 30, 2009; 86 FR 34515, June 29, 2021; 88 FR 4665, Jan. 24, 2023] § 1048.505 How do I test engines using steady-state duty cycles, including ramped-modal testing? This section describes how to test engines under steady-state conditions. In some cases, we allow you to choose the appropriate steady-state duty cycle for an engine; you may also choose between discrete-mode and ramped-modal testing. In all cases, you must use the duty cycle you select in your application for certification for all testing you perform for that engine family. If we test your engines to confirm that they meet emission standards, we will use the duty cycles you select for your own testing. If you submit certification test data using more than one duty cycle, any of the selected duty cycles may be used for any subsequent testing. We may also perform other testing as allowed by the Clean Air Act. (a) You may perform steady-state testing with either discrete-mode or ramped-modal cycles described in 40 CFR Part 1065. (b) Measure emissions by testing the engine on a dynamometer with one or more of the following sets of duty cycles to determine whether it meets the steady-state emission standards in § 1048.101(b): (1) For engines from an engine family that will be used only in variable-speed applications, use one of the following duty cycles: (i) The following duty cycle applies for discrete-mode testing: Table 1 of § 1048.505 C2 mode No. Engine speed 1 Torque 2 Weighting 1 Maximum test speed 25 0.06 2 Intermediate test 100 0.02 3 Intermediate test 75 0.05 4 Intermediate test 50 0.32 5 Intermediate test 25 0.30 6 Intermediate test 10 0.10 7 Warm idle 0 0.15 1 2 (ii) The following duty cycle applies for ramped-modal testing: Table 2 of § 1048.505 RMC mode Time in mode Engine speed 1 2 Torque 2 3 1a Steady-state 119 Warm idle 0 1b Transition 20 Linear transition Linear transition. 2a Steady-state 29 Intermediate speed 100 2b Transition 20 Intermediate speed Linear transition. 3a Steady-state 150 Intermediate speed 10 3b Transition 20 Intermediate speed Linear transition. 4a Steady-state 80 Intermediate speed 75 4b Transition 20 Intermediate speed Linear transition. 5a Steady-state 513 Intermediate speed 25 5b Transition 20 Intermediate speed Linear transition. 6a Steady-state 549 Intermediate speed 50 6b Transition 20 Linear transition Linear transition. 7a Steady-state 96 Maximum test speed 25 7b Transition 20 Linear transition Linear transition. 8 Steady-state 124 Warm idle 0 1 2 3 (2) For engines from an engine family that will be used only at a single, rated speed, use the 5-mode duty cycle or the corresponding ramped-modal cycle described in 40 CFR part 1039, Appendix II, paragraph (a). (3) Use a duty cycle from both paragraphs (b)(1) and (b)(2) of this section if you will not restrict an engine family to constant-speed or variable-speed applications. (4) Use a duty cycle specified in paragraph (b)(2) of this section for all severe-duty engines. (5) For high-load engines, use one of the following duty cycles: (i) The following duty cycle applies for discrete-mode testing: Table 3 of § 1048.505 Mode No. Engine Torque 1 Minimum time in mode (minutes) Weighting factors 1 Maximum test speed 100 3.0 0.50 2 Maximum test speed 75 3.0 0.50 1 (ii) The following duty cycle applies for discrete-mode testing: Table 4 of § 1048.505 RMC modes Time in mode Engine speed Torque 1 2 1a Steady-state 290 Engine governed 100 1b Transition 20 Engine governed Linear transition. 2 Steady-state 290 Engine governed 75 1 2 (c) For full-load operating modes, operate the engine at wide-open throttle. [73 FR 59239, Oct. 8, 2008, as amended at 75 FR 23022, Apr. 30, 2010;79 FR 23751. Apr. 28, 2014] § 1048.510 What transient duty cycles apply for laboratory testing? (a) Starting with the 2007 model year, measure emissions by testing the engine on a dynamometer with the duty cycle described in Appendix II to determine whether it meets the transient emission standards in § 1048.101(a). (b) Calculate cycle statistics and compare with the established criteria as specified in 40 CFR 1065.514 to confirm that the test is valid. (c) Warm up the test engine as follows before running a transient test: (1) Operate the engine for the first 180 seconds of the appropriate duty cycle, then allow it to idle without load for 30 seconds. At the end of the 30-second idling period, start measuring emissions as the engine operates over the prescribed duty cycle. For severe-duty engines, this engine warm-up procedure may include up to 15 minutes of operation over the appropriate duty cycle. (2) If the engine was already operating before a test, use good engineering judgment to let the engine cool down enough so measured emissions during the next test will accurately represent those from an engine starting at room temperature. For example, if an engine starting at room temperature warms up enough in three minutes to start closed-loop operation and achieve full catalyst activity, then minimal engine cooling is necessary before starting the next test. (3) You are not required to measure emissions while the engine is warming up. However, you must design your emission-control system to start working as soon as possible after engine starting. In your application for certification, describe how your engine meets this objective (see § 1048.205(b)). [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40478, July 13, 2005; 73 FR 59241, Oct. 8, 2008; 75 FR 23023, Apr. 30, 2010] § 1048.515 What are the field-testing procedures? (a) This section describes the procedures to determine whether your engines meet the field-testing emission standards in § 1048.101(c). These procedures may include any normal engine operation and ambient conditions that the engines may experience in use. Paragraph (b) of this section defines the limits of what we will consider normal engine operation and ambient conditions. Use the test procedures we specify in § 1048.501, except for the provisions we specify in this section. Measure emissions with one of the following procedures: (1) Remove the selected engines for testing in a laboratory. You may use an engine dynamometer to simulate normal operation, as described in this section. (2) Test the selected engines while they remain installed in the equipment. In 40 CFR part 1065, subpart J, we describe the equipment and sampling methods for testing engines in the field. Use fuel meeting the specifications of 40 CFR part 1065, subpart H, or a fuel typical of what you would expect the engine to use in service. (b) An engine's emissions may not exceed the levels we specify in § 1048.101(c) for any continuous sampling period of at least 120 seconds under the following ranges of operation and operating conditions: (1) Engine operation during the emission sampling period may include any normal operation, subject to the following restrictions: (i) Average power must be at least 5 percent of maximum brake power. (ii) Continuous time at idle must not be greater than 120 seconds. (iii) The sampling period may not begin until the engine has reached stable operating temperatures. For example, this would exclude engine operation after starting until the thermostat starts modulating coolant temperature. (iv) The sampling period may not include engine starting. (v) For engines that qualify for the alternate Tier 2 emission standards in § 1048.101(d), operation at 90 percent or more of maximum power must be less than 10 percent of the total sampling time. You may request our approval for a different power threshold. (2) Engine testing may occur under any normal conditions without correcting measured emission levels, subject to the following restrictions: (i) Barometric pressure must be between 80.0 and 103.3 kPa (600 and 775 mm Hg). (ii) Ambient air temperature must be between 13° and 35 °C. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40478, July 13, 2005; 73 FR 59241, Oct. 8, 2008] Subpart G—Compliance Provisions § 1048.601 What compliance provisions apply to these engines? (a) Engine and equipment manufacturers, as well as owners, operators, and rebuilders of engines subject to the requirements of this part, and all other persons, must observe the provisions of this part, the requirements and prohibitions in 40 CFR part 1068, and the provisions of the Act. (b) This paragraph (b) describes how the replacement-engine provisions of 40 CFR 1068.240 apply for engines subject to the requirements of this part in conjunction with the secondary engine manufacturer provisions in 40 CFR 1068.262. For cases in which the secondary engine manufacturer completes assembly of the engine, these provisions apply as written. If the secondary engine manufacturer arranges for a third party to complete engine assembly, the following additional provisions apply: (1) The ultimate purchaser must purchase (or otherwise order) the replacement engine from the secondary engine manufacturer. The secondary engine manufacturer must provide assembly instructions to the engine assembler (unless the engine being replaced was not subject to emission standards). The secondary engine manufacturer may arrange for the original engine manufacturer to ship the engine directly to the engine assembler. However, if the secondary engine manufacturer does not take possession of the engine, it must supply the engine label specified in 40 CFR 1068.240 to the engine assembler and the engine assembler must apply the label before shipping the engine. (2) The secondary engine manufacturer and engine assembler are both responsible if the engine is installed in new equipment or otherwise violates the circumvention provisions of 40 CFR 1068.240. (3) Consider the following example. A secondary engine manufacturer receiving a valid request for a replacement engine for which it does not already have an engine available in inventory may order a partially complete engine from an original engine manufacturer and have it shipped directly to an independent engine assembler. In this case, the secondary engine manufacturer must state in its order that the partially complete engine should be labeled as being exempt under 40 CFR 1068.240 and identify the engine assembler's address; the secondary engine manufacture must also provide instructions to the engine assembler. The original engine manufacturer would label the engine as described in 40 CFR 1068.262, identifying the replacement-engine exemption as the basis for shipping an uncertified engine, and ship the engine directly to the assembler. The engine assembler would complete the assembly by applying the label and otherwise following the instructions provided by the secondary engine manufacturer. [73 FR 59241, Oct. 8, 2008] § 1048.605 What provisions apply to engines certified under the motor vehicle program? (a) General provisions. (b) Equipment-manufacturer provisions. (c) Liability. (d) Specific requirements. (1) Your engine must be covered by a valid certificate of conformity issued under 40 CFR part 86. (2) You must not make any changes to the certified engine that could reasonably be expected to increase its exhaust emissions for any pollutant, or its evaporative emissions. For example, if you make any of the following changes to one of these engines, you do not qualify for this exemption: (i) Change any fuel system or evaporative system parameters from the certified configuration (this does not apply to refueling controls). (ii) Change, remove, or fail to properly install any other component, element of design, or calibration specified in the engine manufacturer's application for certification. This includes aftertreatment devices and all related components. (iii) Modify or design the engine cooling system so that temperatures or heat rejection rates are outside the original engine manufacturer's specified ranges. (3) You must show that fewer than 50 percent of the engine family's total sales in the United States are used in nonroad applications. This includes engines used in any application without regard to which company manufactures the vehicle or equipment. Show this as follows: (i) If you are the original manufacturer of the engine, base this showing on your sales information. (ii) In all other cases, you must get the original manufacturer of the engine to confirm this based on its sales information. (4) You must ensure that the engine has the label we require under 40 CFR part 86. (5) You must add a permanent supplemental label to the engine in a position where it will remain clearly visible after installation in the equipment. In the supplemental label, do the following: (i) Include the heading: “NONROAD ENGINE EMISSION CONTROL INFORMATION”. (ii) Include your full corporate name and trademark. You may instead include the full corporate name and trademark of another company you choose to designate. (iii) State: “THIS ENGINE WAS ADAPTED FOR NONROAD USE WITHOUT AFFECTING ITS EMISSION CONTROLS. THE EMISSION-CONTROL SYSTEM DEPENDS ON THE USE OF FUEL MEETING SPECIFICATIONS THAT APPLY FOR MOTOR-VEHICLE APPLICATIONS. OPERATING THE ENGINE ON OTHER FUELS MAY BE A VIOLATION OF FEDERAL LAW.”. (iv) State the date you finished modifying the engine (month and year), if applicable. (6) The original and supplemental labels must be readily visible after the engine is installed in the equipment or, if the equipment obscures the engine's emission control information label, the equipment manufacturer must attach duplicate labels, as described in 40 CFR 1068.105. (7) Send the Designated Compliance Officer a signed letter by the end of each calendar year (or less often if we tell you) with all the following information: (i) Identify your full corporate name, address, and telephone number. (ii) List the engine or equipment models you expect to produce under this exemption in the coming year and describe your basis for meeting the sales restrictions of paragraph (d)(3) of this section. (iii) State: “We produce each listed [engine or equipment] model for nonroad application without making any changes that could increase its certified emission levels, as described in 40 CFR 1048.605.”. (e) Failure to comply. (f) Data submission. (g) Participation in averaging, banking and trading. [70 FR 40479, July 13, 2005, as amended at 73 FR 59241, Oct. 8, 2008] § 1048.610 What provisions apply to vehicles certified under the motor vehicle program? (a) General provisions. (b) Equipment-manufacturer provisions. (c) Liability. (d) Specific requirements. (1) Your equipment must be covered by a valid certificate of conformity as a motor vehicle issued under 40 CFR part 86. (2) You must not make any changes to the certified vehicle that we could reasonably expect to increase its exhaust emissions for any pollutant, or its evaporative emissions if it is subject to evaporative-emission standards. For example, if you make any of the following changes, you do not qualify for this exemption: (i) Change any fuel system or evaporative system parameters from the certified configuration, including refueling emission controls. (ii) Change, remove, or fail to properly install any other component, element of design, or calibration specified in the vehicle manufacturer's application for certification. This includes aftertreatment devices and all related components. (iii) Modify or design the engine cooling system so that temperatures or heat rejection rates are outside the original vehicle manufacturer's specified ranges. (iv) Add more than 500 pounds to the curb weight of the originally certified motor vehicle. (3) You must show that fewer than 50 percent of the engine family's total sales in the United States are used in nonroad applications. This includes any type of vehicle, without regard to which company completes the manufacturing of the nonroad equipment. Show this as follows: (i) If you are the original manufacturer of the vehicle, base this showing on your sales information. (ii) In all other cases, you must get the original manufacturer of the vehicle to confirm this based on their sales information. (4) The equipment must have the vehicle emission control information and fuel labels we require under 40 CFR 86.007-35. (5) You must add a permanent supplemental label to the equipment in a position where it will remain clearly visible. In the supplemental label, do the following: (i) Include the heading: “NONROAD ENGINE EMISSION CONTROL INFORMATION”. (ii) Include your full corporate name and trademark. You may instead include the full corporate name and trademark of another company you choose to designate. (iii) State: “THIS VEHICLE WAS ADAPTED FOR NONROAD USE WITHOUT AFFECTING ITS EMISSION CONTROLS. THE EMISSION-CONTROL SYSTEM DEPENDS ON THE USE OF FUEL MEETING SPECIFICATIONS THAT APPLY FOR MOTOR-VEHICLE APPLICATIONS. OPERATING THE ENGINE ON OTHER FUELS MAY BE A VIOLATION OF FEDERAL LAW.”. (iv) State the date you finished modifying the vehicle (month and year), if applicable. (6) The original and supplemental labels must be readily visible in the fully assembled equipment. (7) Send the Designated Compliance Officer a signed letter by the end of each calendar year (or less often if we tell you) with all the following information: (i) Identify your full corporate name, address, and telephone number. (ii) List the equipment models you expect to produce under this exemption in the coming year and describe your basis for meeting the sales restrictions of paragraph (d)(3) of this section. (ii) List the equipment models you expect to produce under this exemption in the coming year. (iii) State: “We produced each listed engine or equipment model for nonroad application without making any changes that could increase its certified emission levels, as described in 40 CFR 1048.610.”. (e) Failure to comply. (f) Data submission. (g) Participation in averaging, banking and trading. [70 FR 40480, July 13, 2005, as amended at 73 FR 59241, Oct. 8, 2008] § 1048.612 What is the exemption for delegated final assembly? The provisions of 40 CFR 1068.261 related to delegated final assembly apply for engines certified under this part 1048, with the following exceptions and clarifications: (a) The provisions related to reduced auditing rates in 40 CFR 1068.261(d)(3)(iii) apply starting with the 2014 model year. (b) [Reserved] [73 FR 59242, Oct. 8, 2008] § 1048.615 What are the provisions for exempting engines designed for lawn and garden applications? This section is intended for engines designed for lawn and garden applications, but it applies to any engines meeting the criteria in paragraph (a) of this section. (a) If an engine meets all the following criteria, it is exempt from the requirements of this part: (1) The engine must have a nominal displacement of 1000 cc or less. (2) The engine must have a maximum engine power at or below 30 kW. (3) The engine must be in an engine family that has a valid certificate of conformity showing that it meets emission standards for Class II engines under 40 CFR part 90 or 1054 for the appropriate model year. (b) The only requirements or prohibitions from this part that apply to an engine that meets the criteria in paragraph (a) of this section are in this section. (c) If your engines do not meet the criteria listed in paragraph (a) of this section, they will be subject to the provisions of this part. Introducing these engines into commerce without a valid exemption or certificate of conformity violates the prohibitions in 40 CFR 1068.101. (d) Engines exempted under this section are subject to all the requirements affecting engines under 40 CFR part 90 or 1054. The requirements and restrictions of 40 CFR part 90 or 1054 apply to anyone manufacturing these engines, anyone manufacturing equipment that uses these engines, and all other persons in the same manner as if these engines had a total maximum engine power at or below 19 kW. [73 FR 59242, Oct. 8, 2008] § 1048.620 What are the provisions for exempting large engines fueled by natural gas or liquefied petroleum gas? (a) If an engine meets all the following criteria, it is exempt from the requirements of this part: (1) The engine must operate solely on natural gas or liquefied petroleum gas. (2) The engine must have maximum engine power at or above 250 kW. (3) The engine must be in an engine family that has a valid certificate of conformity showing that it meets emission standards for engines of that power rating under 40 CFR part 1039. (b) The only requirements or prohibitions from this part that apply to an engine that is exempt under this section are in this section. (c) If your engines do not meet the criteria listed in paragraph (a) of this section, they will be subject to the provisions of this part. Introducing these engines into commerce without a valid exemption or certificate of conformity violates the prohibitions in 40 CFR 1068.101. (d) Engines exempted under this section are subject to all the requirements affecting engines under 40 CFR part 1039. The requirements and restrictions of 40 CFR part 1039 apply to anyone manufacturing engines exempted under this section, anyone manufacturing equipment that uses these engines, and all other persons in the same manner as if these were nonroad diesel engines. (e) You may request an exemption under this section by submitting an application for certification for the engines under 40 CFR part 1039. [70 FR 40481, July 13, 2005, as amended at 88 FR 4665, Jan. 24, 2023] § 1048.625 What special provisions apply to engines using noncommercial fuels? In § 1048.115(e), we generally require that engines meet emission standards for any adjustment within the full range of any adjustable parameters. For engines that use noncommercial fuels significantly different than the specified test fuel of the same type, you may ask to use the parameter-adjustment provisions of this section instead of those in § 1048.115(e). Engines certified under this section must be in a separate engine family. (a) If we approve your request, the following provisions apply: (1) You must certify the engine using the test fuel specified in § 1048.501. (2) You may produce the engine without limits or stops that keep the engine adjusted within the certified range. (3) You must specify in-use adjustments different than the adjustable settings appropriate for the specified test fuel, consistent with the provisions of paragraph (b)(1) of this section. (b) To produce engines under this section, you must do the following: (1) Specify in-use adjustments needed so the engine's level of emission control for each regulated pollutant is equivalent to that from the certified configuration. (2) Add the following information to the emission control information label specified in § 1048.135: (i) Include instructions describing how to adjust the engine to operate in a way that maintains the effectiveness of the emission-control system. (ii) State: “THIS ENGINE IS CERTIFIED TO OPERATE IN APPLICATIONS USING NONCOMMERCIAL FUEL. MALADJUSTMENT OF THE ENGINE IS A VIOLATION OF FEDERAL LAW SUBJECT TO CIVIL PENALTY.”. (3) Keep records to document the destinations and quantities of engines produced under this section. [70 FR 40481, July 13, 2005] § 1048.630 What are the provisions for exempting engines used solely for competition? We may grant you an exemption from the standards and requirements of this part for a new engine on the grounds that it is to be used solely for competition under the provisions of 40 CFR 1054.620. The requirements of this part do not apply to engines that we exempt for use solely for competition. [73 FR 59242, Oct. 8, 2008] § 1048.635 What special provisions apply to branded engines? The following provisions apply if you identify the name and trademark of another company instead of your own on your emission control information label, as provided by § 1048.135(c)(2): (a) You must have a contractual agreement with the other company that obligates that company to take the following steps: (1) Meet the emission warranty requirements that apply under § 1048.120. This may involve a separate agreement involving reimbursement of warranty-related expenses. (2) Report all warranty-related information to the certificate holder. (b) In your application for certification, identify the company whose trademark you will use. (c) You remain responsible for meeting all the requirements of this chapter, including warranty and defect-reporting provisions. [70 FR 40481, July 13, 2005, as amended at 73 FR 59242, Oct. 8, 2008] § 1048.640 What special provisions apply for small-volume engine manufacturers? This section describes how we apply the special provisions in this part for small-volume engine manufacturers. (a) Special provisions apply for small-volume engine manufacturers, as illustrated by the following examples: (1) Waived requirements related to torque broadcasting. See § 1048.115. (2) Assigned deterioration factors to reduce testing burden. See § 1048.240. (3) Additional special provisions apply for small-volume engine and equipment manufacturers under 40 CFR part 1068. For example, see 40 CFR 1068.250. (b) If you use any of the provisions of this part that apply specifically to small-volume engine manufacturers and we find that you do not qualify to use these provisions, we may consider you to be in violation of the requirements that apply for companies that are not small-volume engine manufacturers. If you no longer qualify as a small-volume engine manufacturer (based on increased production volumes or other factors), we will work with you to determine a reasonable schedule for complying with additional requirements that apply. For example, if you no longer qualify as a small-volume engine manufacturer shortly before you certify your engines for the next model year, we might allow you to use assigned deterioration factors for one more model year. [73 FR 59242, Oct. 8, 2008] Subpart H [Reserved] Subpart I—Definitions and Other Reference Information § 1048.801 What definitions apply to this part? The following definitions apply to this part. The definitions apply to all subparts unless we note otherwise. All undefined terms have the meaning the Act gives to them. The definitions follow: Act Adjustable parameter Aftertreatment Aircraft Alcohol-fueled engine All-terrain Amphibious vehicle Auxiliary emission-control device Blue Sky Series engine Brake power Calibration Carryover Certification Certified emission level Compression-ignition Constant-speed engine Constant-speed operation Crankcase emissions Critical emission-related component Date of manufacture Days Designated Compliance Officer Designated Enforcement Officer Deteriorated emission level Deterioration factor (1) For multiplicative deterioration factors, the ratio of emissions at the end of useful life to emissions at the low-hour test point. (2) For additive deterioration factors, the difference between emissions at the end of useful life and emissions at the low-hour test point. Discrete-mode Emission-control system Emission-data engine Emission-related maintenance Engine Engine configuration Engine family Engine manufacturer Equipment manufacturer Excluded (1) Has been determined not to be a nonroad engine, as specified in 40 CFR 1068.30; or (2) Is a nonroad engine that, according to § 1048.5, is not subject to this part 1048. Exempted Exhaust-gas recirculation Fuel system Fuel type Good engineering judgment High-cost warranted part High-load engine Hydrocarbon (HC) Identification number Intermediate test speed Low-hour Manufacturer Marine engine (1) Propulsion marine engine means a marine engine that moves a vessel through the water or directs the vessel's movement. (2) Auxiliary marine engine means a marine engine not used for propulsion. Marine vessel Maximum engine power (1) For engines at or below 100 kW, maximum engine power has the meaning given in 40 CFR 90.3 for 2010 and earlier model years and in 40 CFR 1054.140 for 2011 and later model years. (2) For engines above 100 kW, maximum engine power has the meaning given in 40 CFR 1039.140. Maximum test speed (1) For variable-speed engines, maximum test speed has the meaning given in 40 CFR 1065.1001. (2) For transient testing of constant-speed engines, maximum test speed means the highest speed at which the engine produces zero torque. (3) For steady-state testing of constant-speed engines, maximum test speed means the speed at which the engine produces peak torque. Maximum test torque Model year (1) For freshly manufactured equipment and engines (see definition of “new nonroad engine,” paragraph (1)), model year means one of the following: (i) Calendar year. (ii) Your annual new model production period if it is different than the calendar year. This must include January 1 of the calendar year for which the model year is named. It may not begin before January 2 of the previous calendar year and it must end by December 31 of the named calendar year. (2) For an engine that is converted to a nonroad engine after being placed into service as a stationary engine, or being certified and placed into service as a motor vehicle engine, model year means the calendar year in which the engine was originally produced. For a motor vehicle engine that is converted to be a nonroad engine without having been certified, model year means the calendar year in which the engine becomes a new nonroad engine. (See definition of “new nonroad engine,” paragraph (2)). (3) For a nonroad engine excluded under § 1048.5 that is later converted to operate in an application that is not excluded, model year means the calendar year in which the engine was originally produced (see definition of “new nonroad engine,” paragraph (3)). (4) For engines that are not freshly manufactured but are installed in new nonroad equipment, model year means the calendar year in which the engine is installed in the new nonroad equipment (see definition of “new nonroad engine,” paragraph (4)). (5) For imported engines: (i) For imported engines described in paragraph (5)(i) of the definition of “new nonroad engine,” model year (ii) For imported engines described in paragraph (5)(ii) of the definition of “new nonroad engine,” model year (iii) For imported engines described in paragraph (5)(iii) of the definition of “new nonroad engine,” model year Motor vehicle New nonroad engine (1) A freshly manufactured nonroad engine for which the ultimate purchaser has never received the equitable or legal title. This kind of engine might commonly be thought of as “brand new.” In the case of this paragraph (1), the engine is new from the time it is produced until the ultimate purchaser receives the title or the product is placed into service, whichever comes first. (2) An engine originally manufactured as a motor vehicle engine or a stationary engine that is later used or intended to be used in a piece of nonroad equipment. In this case, the engine is no longer a motor vehicle or stationary engine and becomes a “new nonroad engine.” The engine is no longer new when it is placed into nonroad service. This paragraph (2) applies if a motor vehicle engine or a stationary engine is installed in nonroad equipment, or if a motor vehicle or a piece of stationary equipment is modified (or moved) to become nonroad equipment. (3) A nonroad engine that has been previously placed into service in an application we exclude under § 1048.5, when that engine is installed in a piece of equipment that is covered by this part 1048. The engine is no longer new when it is placed into nonroad service covered by this part 1048. For example, this would apply to a marine-propulsion engine that is no longer used in a marine vessel but is instead installed in a piece of nonroad equipment subject to the provisions of this part. (4) An engine not covered by paragraphs (1) through (3) of this definition that is intended to be installed in new nonroad equipment. This generally includes installation of used engines in new equipment. The engine is no longer new when the ultimate purchaser receives a title for the equipment or the product is placed into service, whichever comes first. (5) An imported nonroad engine, subject to the following provisions: (i) An imported nonroad engine covered by a certificate of conformity issued under this part that meets the criteria of one or more of paragraphs (1) through (4) of this definition, where the original engine manufacturer holds the certificate, is new as defined by those applicable paragraphs. (ii) An imported engine covered by a certificate of conformity issued under this part, where someone other than the original engine manufacturer holds the certificate (such as when the engine is modified after its initial assembly), is a new nonroad engine when it is imported. It is no longer new when the ultimate purchaser receives a title for the engine or it is placed into service, whichever comes first. (iii) An imported nonroad engine that is not covered by a certificate of conformity issued under this part at the time of importation is new. This addresses uncertified engines and equipment initially placed into service that someone seeks to import into the United States. Importation of this kind of engine (or equipment containing such an engine) is generally prohibited by 40 CFR part 1068. However, the importation of such an engine is not prohibited if the engine has a model year before 2004, since it is not subject to standards. New nonroad equipment (1) A nonroad piece of equipment for which the ultimate purchaser has never received the equitable or legal title. The product is no longer new when the ultimate purchaser receives this title or the product is placed into service, whichever comes first. (2) An imported nonroad piece of equipment with an engine not covered by a certificate of conformity issued under this part at the time of importation and manufactured after January 1, 2004. Noncommercial fuel Noncompliant engine Nonconforming engine Nonmethane hydrocarbon Nonroad Nonroad engine Nonroad equipment Off-highway motorcycle Official emission result Owners manual Oxides of nitrogen Piece of equipment Placed into service Point of first retail sale Ramped-modal Rated speed Revoke Round Scheduled maintenance Sealed Severe-duty application Severe-duty engine Small-volume engine manufacturer (1) An engine manufacturer with U.S.-directed production volumes of engines subject to the requirements of this part totaling no more than 2,000 units in any year. This includes engines produced by parent or subsidiary companies. (2) An engine manufacturer with fewer than 200 employees. This includes any employees working for parent or subsidiary companies. Snowmobile Spark-ignition Steady-state Stoichiometric Suspend Test engine Test sample Tier 1 Tier 2 Total hydrocarbon Total hydrocarbon equivalent Ultimate purchaser United States Upcoming model year U.S.-directed production volume Useful life Variable-speed engine Variable-speed operation Void Volatile liquid fuel Wide-open throttle We (us, our) [70 FR 40482, July 13, 2005, as amended at 73 FR 59242, Oct. 8, 2008; 74 FR 8426, Feb. 24, 2009; 75 FR 23023, Apr. 30, 2010; 88 FR 4665, Jan. 24, 2023] § 1048.805 What symbols, acronyms, and abbreviations does this part use? The following symbols, acronyms, and abbreviations apply to this part: °C degrees Celsius. ASTM American Society for Testing and Materials. cc cubic centimeters. CFR Code of Federal Regulations. CH 4 cm centimeter. CO carbon monoxide. CO 2 EPA Environmental Protection Agency. g/kW-hr grams per kilowatt-hour. HC hydrocarbon. ISO International Organization for Standardization. kPa kilopascals. kW kilowatts. LPG liquefied petroleum gas. m meters. MIL malfunction-indicator light. mm Hg millimeters of mercury. N 2 NARA National Archives and Records Administration. NMHC nonmethane hydrocarbons. NO X 2 psi pounds per square inch of absolute pressure. psig pounds per square inch of gauge pressure. rpm revolutions per minute. SAE Society of Automotive Engineers. SI spark-ignition. THC total hydrocarbon. THCE total hydrocarbon equivalent. U.S.C. United States Code. [67 FR 68347, Nov. 8, 2002, as amended at 70 FR 40485, July 13, 2005; 74 FR 56510, Oct. 30, 2009] § 1048.810 What materials does this part reference? (a) Certain material is incorporated by reference into this part with the approval of the Director of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, the Environmental Protection Agency must publish a notice of the change in the Federal Register http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (b) Society of Automotive Engineers, 400 Commonwealth Dr., Warrendale, PA 15096-0001, (877) 606-7323 (U.S. and Canada) or (724) 776-4970 (outside the U.S. and Canada), http://www.sae.org. (1) SAE J2260, Nonmetallic Fuel System Tubing with One or More Layers, November 2004; IBR approved for § 1048.105(a). (2) SAE J2260, Nonmetallic Fuel System Tubing with One or More Layers, November 1996; IBR approved for § 1048.105(a). (c) International Organization for Standardization, Case Postale 56, CH-1211 Geneva 20, Switzerland, (41) 22749 0111, http://www.iso.org, [email protected]. (1) ISO 9141-2 Road vehicles—Diagnostic systems— Part 2: CARB requirements for interchange of digital information, February 1994; IBR approved for § 1048.110(g). (2) ISO 14230-4 Road vehicles—Diagnostic systems—Keyword Protocol 2000—Part 4: Requirements for emission-related systems, June 2000; IBR approved for § 1048.110(g). [78 FR 36397, June 17, 2013] § 1048.815 What provisions apply to confidential information? The provisions of 40 CFR 1068.10 and 1068.11 apply for information you submit under this part. [88 FR 4666, Jan. 24, 2023] § 1048.820 How do I request a hearing? (a) You may request a hearing under certain circumstances, as described elsewhere in this part. To do this, you must file a written request, including a description of your objection and any supporting data, within 30 days after we make a decision. (b) For a hearing you request under the provisions of this part, we will approve your request if we find that your request raises a substantial factual issue. (c) If we agree to hold a hearing, we will use the procedures specified in 40 CFR part 1068, subpart G. [70 FR 40486, July 13, 2005] § 1048.825 What reporting and recordkeeping requirements apply under this part? Under the Paperwork Reduction Act (44 U.S.C. 3501 et seq. (a) We specify the following requirements related to engine certification in this part 1048: (1) In § 1048.20 we require manufacturers of stationary engines to label their engines in certain cases. (2) In § 1048.135 we require engine manufacturers to keep certain records related to duplicate labels sent to equipment manufacturers. (3) In § 1048.145 we include various reporting and recordkeeping requirements related to interim provisions. (4) In subpart C of this part we identify a wide range of information required to certify engines. (5) In §§ 1048.345 and 1048.350 we specify certain records related to production-line testing. (6) In §§ 1048.420 and 1048.425 we specify certain records related to in-use testing. (7) In subpart G of this part we identify several reporting and recordkeeping items for making demonstrations and getting approval related to various special compliance provisions. (b) [Reserved] (c) We specify the following requirements related to testing in 40 CFR part 1065: (1) In 40 CFR 1065.2 we give an overview of principles for reporting information. (2) In 40 CFR 1065.10 and 1065.12 we specify information needs for establishing various changes to published test procedures. (3) In 40 CFR 1065.25 we establish basic guidelines for storing test information. (4) In 40 CFR 1065.695 we identify data that may be appropriate for collecting during testing of in-use engines using portable analyzers. (d) We specify the following requirements related to the general compliance provisions in 40 CFR part 1068: (1) In 40 CFR 1068.5 we establish a process for evaluating good engineering judgment related to testing and certification. (2) In 40 CFR 1068.25 we describe general provisions related to sending and keeping information. (3) In 40 CFR 1068.27 we require manufacturers to make engines available for our testing or inspection if we make such a request. (4) In 40 CFR 1068.105 we require equipment manufacturers to keep certain records related to duplicate labels from engine manufacturers. (5) In 40 CFR 1068.120 we specify recordkeeping related to rebuilding engines. (6) In 40 CFR part 1068, subpart C, we identify several reporting and recordkeeping items for making demonstrations and getting approval related to various exemptions. (7) In 40 CFR part 1068, subpart D, we identify several reporting and recordkeeping items for making demonstrations and getting approval related to importing engines. (8) In 40 CFR 1068.450 and 1068.455 we specify certain records related to testing production-line engines in a selective enforcement audit. (9) In 40 CFR 1068.501 we specify certain records related to investigating and reporting emission-related defects. (10) In 40 CFR 1068.525 and 1068.530 we specify certain records related to recalling nonconforming engines. [73 FR 59245, Oct. 8, 2008] Appendix I to Part 1048 [Reserved] Appendix II to Part 1048—Large Spark-ignition (SI) Composite Transient Cycle The following table shows the transient duty-cycle for engines that are not constant-speed engines, as described in § 1048.510: Time(s) Normalized speed (percent) Normalized torque (percent) 0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 9 1 8 10 6 54 11 8 61 12 34 59 13 22 46 14 5 51 15 18 51 16 31 50 17 30 56 18 31 49 19 25 66 20 58 55 21 43 31 22 16 45 23 24 38 24 24 27 25 30 33 26 45 65 27 50 49 28 23 42 29 13 42 30 9 45 31 23 30 32 37 45 33 44 50 34 49 52 35 55 49 36 61 46 37 66 38 38 42 33 39 17 41 40 17 37 41 7 50 42 20 32 43 5 55 44 30 42 45 44 53 46 45 56 47 41 52 48 24 41 49 15 40 50 11 44 51 32 31 52 38 54 53 38 47 54 9 55 55 10 50 56 33 55 57 48 56 58 49 47 59 33 44 60 52 43 61 55 43 62 59 38 63 44 28 64 24 37 65 12 44 66 9 47 67 12 52 68 34 21 69 29 44 70 44 54 71 54 62 72 62 57 73 72 56 74 88 71 75 100 69 76 100 34 77 100 42 78 100 54 79 100 58 80 100 38 81 83 17 82 61 15 83 43 22 84 24 35 85 16 39 86 15 45 87 32 34 88 14 42 89 8 48 90 5 51 91 10 41 92 12 37 93 4 47 94 3 49 95 3 50 96 4 49 97 4 48 98 8 43 99 2 51 100 5 46 101 8 41 102 4 47 103 3 49 104 6 45 105 3 48 106 10 42 107 18 27 108 3 50 109 11 41 110 34 29 111 51 57 112 67 63 113 61 32 114 44 31 115 48 54 116 69 65 117 85 65 118 81 29 119 74 21 120 62 23 121 76 58 122 96 75 123 100 77 124 100 27 125 100 79 126 100 79 127 100 81 128 100 57 129 99 52 130 81 35 131 69 29 132 47 22 133 34 28 134 27 37 135 83 60 136 100 74 137 100 7 138 100 2 139 70 18 140 23 39 141 5 54 142 11 40 143 11 34 144 11 41 145 19 25 146 16 32 147 20 31 148 21 38 149 21 42 150 9 51 151 4 49 152 2 51 153 1 58 154 21 57 155 29 47 156 33 45 157 16 49 158 38 45 159 37 43 160 35 42 161 39 43 162 51 49 163 59 55 164 65 54 165 76 62 166 84 59 167 83 29 168 67 35 169 84 54 170 90 58 171 93 43 172 90 29 173 66 19 174 52 16 175 49 17 176 56 38 177 73 71 178 86 80 179 96 75 180 89 27 181 66 17 182 50 18 183 36 25 184 36 24 185 38 40 186 40 50 187 27 48 188 19 48 189 23 50 190 19 45 191 6 51 192 24 48 193 49 67 194 47 49 195 22 44 196 25 40 197 38 54 198 43 55 199 40 52 200 14 49 201 11 45 202 7 48 203 26 41 204 41 59 205 53 60 206 44 54 207 22 40 208 24 41 209 32 53 210 44 74 211 57 25 212 22 49 213 29 45 214 19 37 215 14 43 216 36 40 217 43 63 218 42 49 219 15 50 220 19 44 221 47 59 222 67 80 223 76 74 224 87 66 225 98 61 226 100 38 227 97 27 228 100 53 229 100 72 230 100 49 231 100 4 232 100 13 233 87 15 234 53 26 235 33 27 236 39 19 237 51 33 238 67 54 239 83 60 240 95 52 241 100 50 242 100 36 243 100 25 244 85 16 245 62 16 246 40 26 247 56 39 248 81 75 249 98 86 250 100 76 251 100 51 252 100 78 253 100 83 254 100 100 255 100 66 256 100 85 257 100 72 258 100 45 259 98 58 260 60 30 261 43 32 262 71 36 263 44 32 264 24 38 265 42 17 266 22 51 267 13 53 268 23 45 269 29 50 270 28 42 271 21 55 272 34 57 273 44 47 274 19 46 275 13 44 276 25 36 277 43 51 278 55 73 279 68 72 280 76 63 281 80 45 282 83 40 283 78 26 284 60 20 285 47 19 286 52 25 287 36 30 288 40 26 289 45 34 290 47 35 291 42 28 292 46 38 293 48 44 294 68 61 295 70 47 296 48 28 297 42 22 298 31 29 299 22 35 300 28 28 301 46 46 302 62 69 303 76 81 304 88 85 305 98 81 306 100 74 307 100 13 308 100 11 309 100 17 310 99 3 311 80 7 312 62 11 313 63 11 314 64 16 315 69 43 316 81 67 317 93 74 318 100 72 319 94 27 320 73 15 321 40 33 322 40 52 323 50 50 324 11 53 325 12 45 326 5 50 327 1 55 328 7 55 329 62 60 330 80 28 331 23 37 332 39 58 333 47 24 334 59 51 335 58 68 336 36 52 337 18 42 338 36 52 339 59 73 340 72 85 341 85 92 342 99 90 343 100 72 344 100 18 345 100 76 346 100 64 347 100 87 348 100 97 349 100 84 350 100 100 351 100 91 352 100 83 353 100 93 354 100 100 355 94 43 356 72 10 357 77 3 358 48 2 359 29 5 360 59 19 361 63 5 362 35 2 363 24 3 364 28 2 365 36 16 366 54 23 367 60 10 368 33 1 369 23 0 370 16 0 371 11 0 372 20 0 373 25 2 374 40 3 375 33 4 376 34 5 377 46 7 378 57 10 379 66 11 380 75 14 381 79 11 382 80 16 383 92 21 384 99 16 385 83 2 386 71 2 387 69 4 388 67 4 389 74 16 390 86 25 391 97 28 392 100 15 393 83 2 394 62 4 395 40 6 396 49 10 397 36 5 398 27 4 399 29 3 400 22 2 401 13 3 402 37 36 403 90 26 404 41 2 405 25 2 406 29 2 407 38 7 408 50 13 409 55 10 410 29 3 411 24 7 412 51 16 413 62 15 414 72 35 415 91 74 416 100 73 417 100 8 418 98 11 419 100 59 420 100 98 421 100 99 422 100 75 423 100 95 424 100 100 425 100 97 426 100 90 427 100 86 428 100 82 429 97 43 430 70 16 431 50 20 432 42 33 433 89 64 434 89 77 435 99 95 436 100 41 437 77 12 438 29 37 439 16 41 440 16 38 441 15 36 442 18 44 443 4 55 444 24 26 445 26 35 446 15 45 447 21 39 448 29 52 449 26 46 450 27 50 451 13 43 452 25 36 453 37 57 454 29 46 455 17 39 456 13 41 457 19 38 458 28 35 459 8 51 460 14 36 461 17 47 462 34 39 463 34 57 464 11 70 465 13 51 466 13 68 467 38 44 468 53 67 469 29 69 470 19 65 471 52 45 472 61 79 473 29 70 474 15 53 475 15 60 476 52 40 477 50 61 478 13 74 479 46 51 480 60 73 481 33 84 482 31 63 483 41 42 484 26 69 485 23 65 486 48 49 487 28 57 488 16 67 489 39 48 490 47 73 491 35 87 492 26 73 493 30 61 494 34 49 495 35 66 496 56 47 497 49 64 498 59 64 499 42 69 500 6 77 501 5 59 502 17 59 503 45 53 504 21 62 505 31 60 506 53 68 507 48 79 508 45 61 509 51 47 510 41 48 511 26 58 512 21 62 513 50 52 514 39 65 515 23 65 516 42 62 517 57 80 518 66 81 519 64 62 520 45 42 521 33 42 522 27 57 523 31 59 524 41 53 525 45 72 526 48 73 527 46 90 528 56 76 529 64 76 530 69 64 531 72 59 532 73 58 533 71 56 534 66 48 535 61 50 536 55 56 537 52 52 538 54 49 539 61 50 540 64 54 541 67 54 542 68 52 543 60 53 544 52 50 545 45 49 546 38 45 547 32 45 548 26 53 549 23 56 550 30 49 551 33 55 552 35 59 553 33 65 554 30 67 555 28 59 556 25 58 557 23 56 558 22 57 559 19 63 560 14 63 561 31 61 562 35 62 563 21 80 564 28 65 565 7 74 566 23 54 567 38 54 568 14 78 569 38 58 570 52 75 571 59 81 572 66 69 573 54 44 574 48 34 575 44 33 576 40 40 577 28 58 578 27 63 579 35 45 580 20 66 581 15 60 582 10 52 583 22 56 584 30 62 585 21 67 586 29 53 587 41 56 588 15 67 589 24 56 590 42 69 591 39 83 592 40 73 593 35 67 594 32 61 595 30 65 596 30 72 597 48 51 598 66 58 599 62 71 600 36 63 601 17 59 602 16 50 603 16 62 604 34 48 605 51 66 606 35 74 607 15 56 608 19 54 609 43 65 610 52 80 611 52 83 612 49 57 613 48 46 614 37 36 615 25 44 616 14 53 617 13 64 618 23 56 619 21 63 620 18 67 621 20 54 622 16 67 623 26 56 624 41 65 625 28 62 626 19 60 627 33 56 628 37 70 629 24 79 630 28 57 631 40 57 632 40 58 633 28 44 634 25 41 635 29 53 636 31 55 637 26 64 638 20 50 639 16 53 640 11 54 641 13 53 642 23 50 643 32 59 644 36 63 645 33 59 646 24 52 647 20 52 648 22 55 649 30 53 650 37 59 651 41 58 652 36 54 653 29 49 654 24 53 655 14 57 656 10 54 657 9 55 658 10 57 659 13 55 660 15 64 661 31 57 662 19 69 663 14 59 664 33 57 665 41 65 666 39 64 667 39 59 668 39 51 669 28 41 670 19 49 671 27 54 672 37 63 673 32 74 674 16 70 675 12 67 676 13 60 677 17 56 678 15 62 679 25 47 680 27 64 681 14 71 682 5 65 683 6 57 684 6 57 685 15 52 686 22 61 687 14 77 688 12 67 689 12 62 690 14 59 691 15 58 692 18 55 693 22 53 694 19 69 695 14 67 696 9 63 697 8 56 698 17 49 699 25 55 700 14 70 701 12 60 702 22 57 703 27 67 704 29 68 705 34 62 706 35 61 707 28 78 708 11 71 709 4 58 710 5 58 711 10 56 712 20 63 713 13 76 714 11 65 715 9 60 716 7 55 717 8 53 718 10 60 719 28 53 720 12 73 721 4 64 722 4 61 723 4 61 724 10 56 725 8 61 726 20 56 727 32 62 728 33 66 729 34 73 730 31 61 731 33 55 732 33 60 733 31 59 734 29 58 735 31 53 736 33 51 737 33 48 738 27 44 739 21 52 740 13 57 741 12 56 742 10 64 743 22 47 744 15 74 745 8 66 746 34 47 747 18 71 748 9 57 749 11 55 750 12 57 751 10 61 752 16 53 753 12 75 754 6 70 755 12 55 756 24 50 757 28 60 758 28 64 759 23 60 760 20 56 761 26 50 762 28 55 763 18 56 764 15 52 765 11 59 766 16 59 767 34 54 768 16 82 769 15 64 770 36 53 771 45 64 772 41 59 773 34 50 774 27 45 775 22 52 776 18 55 777 26 54 778 39 62 779 37 71 780 32 58 781 24 48 782 14 59 783 7 59 784 7 55 785 18 49 786 40 62 787 44 73 788 41 68 789 35 48 790 29 54 791 22 69 792 46 53 793 59 71 794 69 68 795 75 47 796 62 32 797 48 35 798 27 59 799 13 58 800 14 54 801 21 53 802 23 56 803 23 57 804 23 65 805 13 65 806 9 64 807 27 56 808 26 78 809 40 61 810 35 76 811 28 66 812 23 57 813 16 50 814 11 53 815 9 57 816 9 62 817 27 57 818 42 69 819 47 75 820 53 67 821 61 62 822 63 53 823 60 54 824 56 44 825 49 39 826 39 35 827 30 34 828 33 46 829 44 56 830 50 56 831 44 52 832 38 46 833 33 44 834 29 45 835 24 46 836 18 52 837 9 55 838 10 54 839 20 53 840 27 58 841 29 59 842 30 62 843 30 65 844 27 66 845 32 58 846 40 56 847 41 57 848 18 73 849 15 55 850 18 50 851 17 52 852 20 49 853 16 62 854 4 67 855 2 64 856 7 54 857 10 50 858 9 57 859 5 62 860 12 51 861 14 65 862 9 64 863 31 50 864 30 78 865 21 65 866 14 51 867 10 55 868 6 59 869 7 59 870 19 54 871 23 61 872 24 62 873 34 61 874 51 67 875 60 66 876 58 55 877 60 52 878 64 55 879 68 51 880 63 54 881 64 50 882 68 58 883 73 47 884 63 40 885 50 38 886 29 61 887 14 61 888 14 53 889 42 6 890 58 6 891 58 6 892 77 39 893 93 56 894 93 44 895 93 37 896 93 31 897 93 25 898 93 26 899 93 27 900 93 25 901 93 21 902 93 22 903 93 24 904 93 23 905 93 27 906 93 34 907 93 32 908 93 26 909 93 31 910 93 34 911 93 31 912 93 33 913 93 36 914 93 37 915 93 34 916 93 30 917 93 32 918 93 35 919 93 35 920 93 32 921 93 28 922 93 23 923 94 18 924 95 18 925 96 17 926 95 13 927 96 10 928 95 9 929 95 7 930 95 7 931 96 7 932 96 6 933 96 6 934 95 6 935 90 6 936 69 43 937 76 62 938 93 47 939 93 39 940 93 35 941 93 34 942 93 36 943 93 39 944 93 34 945 93 26 946 93 23 947 93 24 948 93 24 949 93 22 950 93 19 951 93 17 952 93 19 953 93 22 954 93 24 955 93 23 956 93 20 957 93 20 958 94 19 959 95 19 960 95 17 961 96 13 962 95 10 963 96 9 964 95 7 965 95 7 966 95 7 967 95 6 968 96 6 969 96 6 970 89 6 971 68 6 972 57 6 973 66 32 974 84 52 975 93 46 976 93 42 977 93 36 978 93 28 979 93 23 980 93 19 981 93 16 982 93 15 983 93 16 984 93 15 985 93 14 986 93 15 987 93 16 988 94 15 989 93 32 990 93 45 991 93 43 992 93 37 993 93 29 994 93 23 995 93 20 996 93 18 997 93 16 998 93 17 999 93 16 1000 93 15 1001 93 15 1002 93 15 1003 93 14 1004 93 15 1005 93 15 1006 93 14 1007 93 13 1008 93 14 1009 93 14 1010 93 15 1011 93 16 1012 93 17 1013 93 20 1014 93 22 1015 93 20 1016 93 19 1017 93 20 1018 93 19 1019 93 19 1020 93 20 1021 93 32 1022 93 37 1023 93 28 1024 93 26 1025 93 24 1026 93 22 1027 93 22 1028 93 21 1029 93 20 1030 93 20 1031 93 20 1032 93 20 1033 93 19 1034 93 18 1035 93 20 1036 93 20 1037 93 20 1038 93 20 1039 93 19 1040 93 18 1041 93 18 1042 93 17 1043 93 16 1044 93 16 1045 93 15 1046 93 16 1047 93 18 1048 93 37 1049 93 48 1050 93 38 1051 93 31 1052 93 26 1053 93 21 1054 93 18 1055 93 16 1056 93 17 1057 93 18 1058 93 19 1059 93 21 1060 93 20 1061 93 18 1062 93 17 1063 93 17 1064 93 18 1065 93 18 1066 93 18 1067 93 19 1068 93 18 1069 93 18 1070 93 20 1071 93 23 1072 93 25 1073 93 25 1074 93 24 1075 93 24 1076 93 22 1077 93 22 1078 93 22 1079 93 19 1080 93 16 1081 95 17 1082 95 37 1083 93 43 1084 93 32 1085 93 27 1086 93 26 1087 93 24 1088 93 22 1089 93 22 1090 93 22 1091 93 23 1092 93 22 1093 93 22 1094 93 23 1095 93 23 1096 93 23 1097 93 22 1098 93 23 1099 93 23 1100 93 23 1101 93 25 1102 93 27 1103 93 26 1104 93 25 1105 93 27 1106 93 27 1107 93 27 1108 93 24 1109 93 20 1110 93 18 1111 93 17 1112 93 17 1113 93 18 1114 93 18 1115 93 18 1116 93 19 1117 93 22 1118 93 22 1119 93 19 1120 93 17 1121 93 17 1122 93 18 1123 93 18 1124 93 19 1125 93 19 1126 93 20 1127 93 19 1128 93 20 1129 93 25 1130 93 30 1131 93 31 1132 93 26 1133 93 21 1134 93 18 1135 93 20 1136 93 25 1137 93 24 1138 93 21 1139 93 21 1140 93 22 1141 93 22 1142 93 28 1143 93 29 1144 93 23 1145 93 21 1146 93 18 1147 93 16 1148 93 16 1149 93 16 1150 93 17 1151 93 17 1152 93 17 1153 93 17 1154 93 23 1155 93 26 1156 93 22 1157 93 18 1158 93 16 1159 93 16 1160 93 17 1161 93 19 1162 93 18 1163 93 16 1164 93 19 1165 93 22 1166 93 25 1167 93 29 1168 93 27 1169 93 22 1170 93 18 1171 93 16 1172 93 19 1173 93 19 1174 93 17 1175 93 17 1176 93 17 1177 93 16 1178 93 16 1179 93 15 1180 93 16 1181 93 15 1182 93 17 1183 93 21 1184 93 30 1185 93 53 1186 93 54 1187 93 38 1188 93 30 1189 93 24 1190 93 20 1191 95 20 1192 96 18 1193 96 15 1194 96 11 1195 95 9 1196 95 8 1197 96 7 1198 94 33 1199 93 46 1200 93 37 1201 16 8 1202 0 0 1203 0 0 1204 0 0 1205 0 0 1206 0 0 1207 0 0 1208 0 0 1209 0 0

Related documents

• 50 CFR Part 600 — Magnuson-Stevens Act Provisions#512148
• 50 CFR Part 622 — Fisheries of the Caribbean, Gulf of America, and South Atlantic#512149
• 50 CFR Part 635 — Atlantic Highly Migratory Species#512150
• 50 CFR Part 648 — Fisheries of the Northeastern United States#512151
• 50 CFR Part 660 — Fisheries off West Coast States#512152