PART 53—HEATING BOILERS Authority: 46 U.S.C. 3306, 3703; E.O. 12234, 45 FR 58801, 3 CFR, 1980 Comp., p. 277; Department of Homeland Security Delegation No. 00170.1, Revision No. 01.3. Source: CGFR 68-82, 33 FR 18826, Dec. 18, 1968, as amended by USCG-2020-0634, 89 FR 50102, June 12, 2024, unless otherwise noted. Subpart 53.01—General Requirements § 53.01-1 Incorporation by reference. Certain material is incorporated by reference into this part with the approval of the Director of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, the Coast Guard must publish a document in the Federal Register [email protected] www.archives.gov/federal-register/cfr/ibr-locations [email protected] (a) American Society of Mechanical Engineers (ASME), [email protected]; www.asme.org (1) ASME BPVC.I-2019, 2019 ASME Boiler and Pressure Vessel Code, Section I, Rules for Construction of Power Boilers, 2019 Edition, issued July 1, 2019 (“Section I of the ASME BPVC”); IBR approved for § 53.01-10(e). (2) ASME BPVC.IV-2019, 2019 ASME Boiler and Pressure Vessel Code, Section IV, Rules for Construction of Heating Boilers, 2019 Edition, issued July 1, 2019 (“Section IV of the ASME BPVC”); IBR approved for §§ 53.01-3; 53.01-5; 53.01-10(a); 53.05-1(a); 53.05-2(a); 53.05-3; 53.05-5; 53.10-1; 53.10-3(a); 53.10-10; 53.10-15; 53.12-1(a). (b) UL Solutions, www.ul.com (1) UL 174, Standard for Safety, Household Electric Storage Tank Water Heaters, Eleventh Edition, dated April 29, 2004, including revisions through December 15, 2016 (“UL 174”); IBR approved for § 53.01-10(c). (2) UL 1453, Standard for Safety, Electric Booster and Commercial Storage Tank Water Heaters, Sixth Edition, dated March 29, 2016, including revisions through March 9, 2017 (“UL 1453”); IBR approved for § 53.01-10(c). [USCG-2003-16630, 73 FR 65163, Oct. 31, 2008, as amended by USCG-2009-0702, 74 FR 49228, Sept. 25, 2009; USCG-2012-0832, 77 FR 59777, Oct. 1, 2012; USCG-2013-0671, 78 FR 60147, Sept. 30, 2013] § 53.01-3 Adoption of Section IV of the ASME BPVC. (a) Heating boilers must be designed, constructed, inspected, tested, and stamped in accordance with Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1) as limited, modified, or replaced by specific requirements in this part. The provisions in the appendices to Section IV of the ASME BPVC are adopted and must be followed when the requirements in Section IV make them mandatory. For general information, table 1 to § 53.01-3(a) lists the various paragraphs in Section IV of the ASME BPVC that are limited, modified, or replaced by regulations in this part. Table 1 to § 53.01-3( a Paragraphs in Section IV of the ASME BPVC and disposition Unit of this part HG-100 modified by 53.01-5(b). HG-101 replaced by 53.01-10. HG-400 modified by 53.05-1. HG-400.2 modified by 53.05-2. HG-401 modified by 53.05-1. HG-401.2 modified by 53.05-3. HG-500 through HG-540 modified by 53.10-3. HG-600 through HG-640 modified by 53.12-1. Note 1 to table § 53.01-3(a): (b) References to the ASME BPVC, such as paragraph HG-307, indicate: (1) H = Section IV of the ASME BPVC. (2) G = Part containing general requirements. (3) 3 = Article in part. (4) 307 = Paragraph within Article 3. (c) When a paragraph or a section of the regulations in this part relates to Section IV of the ASME BPVC, the relationship with the code will be shown immediately following the heading of the section or at the beginning of the paragraph, as follows: (1) (Modifies H__.) This indicates that the material in H__ is generally applicable but is being altered, amplified, or augmented. (2) (Replaces H__.) This indicates that H__ does not apply. (3) (Reproduces H__.) This indicates that H__ is being identically reproduced for convenience, not for emphasis. [CGFR 68-82, 33 FR 18826, Dec. 18, 1968, as amended by CGFR 69-127, 35 FR 9976, June 17, 1970; CGD 81-79, 50 FR 9435, Mar. 8, 1985. Redesignated and amended by CGD 88-032, 56 FR 35821, July 29, 1991; USCG-2003-16630, 73 FR 65163, Oct. 31, 2008] § 53.01-5 Scope (modifies HG-100). (a) The regulations in this part apply to steam heating boilers, hot water boilers (which include hot water heating boilers and hot water supply boilers), and to appurtenances thereto. The requirements in this part must be used in conjunction with Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1). Table 1 to § 54.01-5 of this subchapter gives a breakdown by parts in this subchapter of the regulations governing various types of pressure vessels and boilers. (b) (Modifies HG-100.) The requirements of part HG of Section IV of the ASME BPVC must be used except as noted otherwise in this part. [USCG-2003-16630, 73 FR 65163, Oct. 31, 2008] § 53.01-10 Service restrictions and exceptions (replaces HG-101). (a) General. (b) Service restrictions. (2) Boilers of cast iron materials must be restricted to a maximum of 103 kPa gage (15 psig) for steam and to a maximum of 206 kPa gage (30 psig) or 121 °C (250 °F) for hot water. (c) Hot water supply boilers. (2) Oil fired hot water supply boilers are not exempted from the requirements of this part on the basis of size or heat input. (d) Exhaust gas boilers. (e) ASME BPVC Section I. (1) Be stamped with the appropriate ASME symbol in accordance with Section I of the ASME BPVC; (2) Meet the service restrictions of paragraph (b)(2) of this section if made of cast iron; (3) Have safety valves which meet the requirements of § 52.01-120 of this subchapter; (4) If a hot water supply boiler, have a temperature relief valve or a pressure-temperature relief valve in accordance with § 53.05-2(c); (5) If automatically controlled, meet the applicable requirements in part 63 of this subchapter; and (6) Meet the inspection and test requirements of § 53.10-3. (f) Controls and miscellaneous accessories. [CGFR 68-82, 33 FR 18826, Dec. 18, 1968, as amended by CGD 81-79, 50 FR 9435, Mar. 8, 1985; USCG-2003-16630, 73 FR 65163, Oct. 31, 2008] Subpart 53.05—Pressure Relieving Devices (Article 4) Source: CGD 81-79, 50 FR 9435, Mar. 8, 1985, unless otherwise noted. § 53.05-1 Safety valve requirements for steam boilers (modifies HG-400 and HG-401). (a) The pressure relief valve requirements and the safety valve requirements for steam boilers must be as indicated in HG-400 and HG-401 of Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1) except as noted otherwise in this section. (b) Each steam boiler must have at least one safety valve. [CGD 81-79, 50 FR 9435, Mar. 8, 1985, as amended by USCG-2003-16630, 73 FR 65163, Oct. 31, 2008] § 53.05-2 Relief valve requirements for hot water boilers (modifies HG-400.2). (a) Relief valves. (b) Hot water heating boilers. (c) Hot water supply boilers. [CGD 81-79, 50 FR 9435, Mar. 8, 1985, as amended by USCG-2003-16630, 73 FR 65163, Oct. 31, 2008] § 53.05-3 Materials (modifies HG-401.2). Materials for valves must be in accordance with HG-401.2 of Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1) except that nonmetallic materials may be used only for gaskets and packing. [USCG-2003-16630, 73 FR 65164, Oct. 31, 2008] § 53.05-5 Discharge capacities and valve markings. The discharge capacities and valve markings must be as indicated in HG-402 of Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1). The discharge capacities must be certified by the National Board of Boiler and Pressure Vessel Inspectors. [USCG-2003-16630, 73 FR 65164, Oct. 31, 2008] Subpart 53.10—Tests, Inspection, Stamping, and Reporting (Article 5) § 53.10-1 General. The tests, inspection, stamping, and reporting of heating boilers must be as indicated in article 5, part HG of Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1) except as noted otherwise in this subpart. [USCG-2003-16630, 73 FR 65164, Oct. 31, 2008] § 53.10-3 Inspection and tests (modifies HG-500 through HG-540). (a) The inspections required by HG-500 through HG-540 must be performed by the “Authorized Inspector” as defined in HG-515 of Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1). The Authorized Inspector must hold a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors. After installation, heating boilers must be inspected for compliance with this part by a marine inspector. (b) Automatically controlled boilers must be subjected to the operating tests prescribed in part 63 of this subchapter. (c) All heating boilers must have the operation of their pressure relieving devices checked after the final installation. [CGD 81-79, 50 FR 9436, Mar. 8, 1985, as amended by USCG-2003-16630, 73 FR 65164, Oct. 31, 2008] § 53.10-10 Certification by stamping. Stamping of heating boilers must be as indicated in HG-530 of Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1). [USCG-2003-16630, 73 FR 65164, Oct. 31, 2008] § 53.10-15 Manufacturer's data report forms. The manufacturer's data report forms required by HG-520 of Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1) must be made available to the marine inspector for review. The Authorized Inspector's National Board commission number must be included on the manufacturer's data report forms. [USCG-2003-16630, 73 FR 65164, Oct. 31, 2008] Subpart 53.12—Instruments, Fittings, and Controls (Article 6) § 53.12-1 General (modifies HG-600 through HG-640). (a) The instruments, fittings and controls for heating boilers must be as indicated in HG-600 through HG-640 of Section IV of the ASME BPVC (incorporated by reference; see § 53.01-1) except as noted otherwise in this section. (b) For control systems for automatic auxiliary heating equipment, the requirements in part 63 of this subchapter govern and must be followed. [CGFR 68-82, 33 FR 18826, Dec. 18, 1968, as amended by USCG-2003-16630, 73 FR 65164, Oct. 31, 2008]