46 CFR Part 69 — Measurement of Vessels

PART 69—MEASUREMENT OF VESSELS Authority: 46 U.S.C. 2301, 14103, 14104; Department of Homeland Security Delegation No. 0170.1. Source: CGD 87-015b, 54 FR 37657, Sept. 12, 1989, unless otherwise noted. Subpart A—General § 69.1 Purpose. This part implements legislation concerning the measurement of vessels to determine their tonnage (part J of 46 U.S.C. subtitle II). Tonnage is used for a variety of purposes, including the application of vessel safety, security, and environmental protection regulations and the assessment of taxes and fees. This part indicates the particular measurement system or systems under which the vessel is required or eligible to be measured, describes the measurement rules and procedures for each system, identifies the organizations authorized to measure vessels under this part, and provides for the appeal of measurement organizations' decisions. [USCG-2011-0522, 81 FR 18717, Mar. 31, 2016] § 69.3 Applicability. This part applies to any vessel for which the application of an international agreement or other law of the United States to the vessel depends on the vessel's tonnage. [USCG-2011-0522, 81 FR 18718, Mar. 31, 2016] § 69.5 [Reserved] § 69.7 Vessels transiting the Panama and Suez Canals. For vessels that will transit the Panama Canal and/or Suez Canal, the respective canal authorities may require special tonnage certificates in addition to those issued under this part. These special certificates may be issued by measurement organizations who have received appropriate authorization from the respective canal authorities. [USCG-2011-0522, 81 FR 18718, Mar. 31, 2016] § 69.9 Definitions. As used in this part: Authorized measurement organization Commandant Convention Convention Measurement System Deck cargo Dual Regulatory Measurement System Foreign flag vessel Formal Measurement System Great Lakes Gross register tonnage (GRT) Gross tonnage ITC (GT ITC) National Vessel Documentation Center Net register tonnage (NRT) Non-self-propelled vessel Overall length Portable enclosed space Register ton Regulatory Measurement System Remeasurement Self-propelled vessel Simplified Regulatory Measurement System Standard Regulatory Measurement System Tonnage Tonnage threshold U.S. flag vessel Vessel of war Vessel that engages on a foreign voyage (1) That arrives at a place under the jurisdiction of the United States from a place in a foreign country; (2) That makes a voyage between places outside of the United States; (3) That departs from a place under the jurisdiction of the United States for a place in a foreign country; or (4) That makes a voyage between a place within a territory or possession of the United States and another place under the jurisdiction of the United States not within that territory or possession. [USCG-2011-0522, 81 FR 18718, Mar. 31, 2016] § 69.11 Determining the measurement system or systems for a particular vessel. (a) Convention Measurement System (subpart B of this part). (2) This system does not apply to the following vessels: (i) A vessel of war, unless the government of the country to which the vessel belongs elects to measure the vessel under this part. (ii) A vessel of less than 79 feet in overall length. (iii) A U.S. flag vessel, or one of Canadian registry or nationality, or operated under the authority of Canada, and that is operating only on the Great Lakes, unless the vessel owner requests. (iv) A U.S. flag vessel (except a vessel that engages on a foreign voyage), the keel of which was laid or was at a similar stage of construction before January 1, 1986, unless the vessel owner requests or unless the vessel subsequently undergoes a change that the Commandant finds substantially affects the gross tonnage. (v) A non-self-propelled U.S. flag vessel (except a non-self-propelled vessel that engages on a foreign voyage), unless the vessel owner requests the application. (b) Standard Regulatory Measurement System (subpart C of this part). (c) Dual Regulatory Measurement System (subpart D of this part). (d) Simplified Regulatory Measurement System (subpart E of this part). (1) A vessel that is under 79 feet in overall length. (2) A vessel of any length that is non-self-propelled. (3) A vessel of any length that is operated only for pleasure. [USCG-2011-0522, 81 FR 18719, Mar. 31, 2016] § 69.13 Applying provisions of a measurement system. (a) Except as noted under paragraph (c) of this section, all provisions of a measurement system as prescribed in this part that are applicable to the vessel must be observed. Coast Guard interpretations of these provisions are published by, and may be obtained from, Commanding Officer, Marine Safety Center (MSC-4). (b) The provisions of more than one measurement system must not be applied interchangeably or combined, except where specifically authorized under this part. (c) Unless otherwise provided for by law, the tonnage measurement rules and procedures that immediately predate the rules and procedures prescribed in this part may be applied, at the option of the vessel owner, to the following vessels: (1) A vessel which has not been measured and which was contracted for on or before May 2, 2016. (2) A vessel which has been measured, but which has undergone modifications contracted for on or before May 2, 2016. [USCG-2011-0522, 81 FR 18719, Mar. 31, 2016] § 69.15 Authorized measurement organizations. (a) Except as noted under paragraphs (c) and (d) of this section, measurement or remeasurement of all vessels under the Convention Measurement System and Standard and Dual Regulatory Measurement Systems must be performed by an authorized measurement organization meeting the requirements of § 69.27. A current listing of authorized measurement organizations may be obtained from the Commanding Officer, Marine Safety Center (MSC-4), U.S. Coast Guard, 2703 Martin Luther King Jr. Avenue SE., Washington, DC 20593 or by writing to Commanding Officer (MSC), Attn: Marine Safety Center, U.S. Coast Guard Stop 7430, 2703 Martin Luther King Jr. Avenue SE., Washington, DC 20593-7430. (b) Measurement or remeasurement of all vessels under subpart E of this part must be performed by the Coast Guard. (c) Measurement or remeasurement of all U.S. Coast Guard vessels and all U.S. Navy vessels of war must be performed by the Coast Guard. (d) At the option of the Commandant, the Coast Guard may measure any vessel under this part. (e) The appropriate tonnage certificate, as provided for under this part, is issued by the authorized measurement organization as evidence of the vessel's measurement under this part. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by CGD 92-058, 57 FR 59938, Dec. 17, 1992; CGD 92-053, 59 FR 50508, Oct. 4, 1994; CGD 95-014, 60 FR 31606, June 15, 1995; CGD 97-057, 62 FR 51045, Sept. 30, 1997; USCG-2007-29018, 72 FR 53965, Sept. 21, 2007; USCG-2009-0702, 74 FR 49230, Sept. 25, 2009; USCG-2013-0671, 78 FR 60149, Sept. 30, 2013; USCG-2011-0522, 81 FR 18719, Mar. 31, 2016; USCG-2016-0498, 82 FR 35091, July 28, 2017] § 69.17 Application for measurement services. (a) The vessel owner is responsible for having the vessel measured or remeasured under this part. Applications for Formal Measurement may be obtained from any measurement organization and, once completed, are submitted to the authorized measurement organization that will perform the measurement services. Applications for Simplified Measurement may be obtained from the Commanding Officer, Marine Safety Center (MSC-4) and, once completed, are submitted or retained as described in § 69.205. The contents of the application are described in this part under the requirements for each system. (b) Applications for measurement under more than one system may be combined. (c) For vessels under construction, the application should be submitted before the vessel is advanced in construction. Usually, this means as soon as the decks are laid, holds cleared of encumbrances, engines installed, and accommodations partitioned. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by CGD 97-057, 62 FR 51045, Sept. 30, 1997; USCG-2011-0522, 81 FR 18719, Mar. 31, 2016] § 69.19 Remeasurement. (a) If a vessel that is already measured is to undergo a structural alteration, a change to its service, or if the use of its space is to be changed, a remeasurement may be required. For vessels measured under a Formal Measurement System, owners must report immediately to an authorized measurement organization any intent to structurally alter the vessel or to change its service or the use of its space. The measurement organization advises the owner if remeasurement is necessary. For all other vessels, owners must report the intent to structurally alter the vessel to Commanding Officer, Marine Safety Center (MSC-4), for a remeasurement determination. Remeasurement is initiated by completing and submitting, where applicable, the appropriate application for measurement services. Spaces not affected by the alteration or change need not be remeasured. (b) Remeasurement must also be performed as follows: (1) When there is a perceived error in the application of this part, the vessel owner should contact the responsible measurement organization, or Commanding Officer, Marine Safety Center (MSC-4), as appropriate. Remeasurement is performed to the extent necessary to verify and correct the error. (2) At the vessel owner's option, to reflect the latest tonnage measurement rules and associated interpretations under this part. (c) For vessels measured under a Formal Measurement System, if a remeasurement or adjustment of tonnage is required, the authorized measurement organization will issue a new tonnage certificate. For all other vessels, Commanding Officer, Marine Safety Center (MSC-4) will take action, as appropriate. (d) A vessel of less than 79 feet in overall length measured under a Formal Measurement System may be remeasured at the owner's request under the Simplified Regulatory Measurement System. [USCG-2011-0522, 81 FR 18719, Mar. 31, 2016] § 69.20 Applying tonnage thresholds. (a) General. (b) Thresholds found in international conventions. (1) For vessels measured under the Convention Measurement System, apply all tonnage thresholds using Convention Measurement System tonnage, except as provided for under the following international tonnage grandfathering provisions, which may be applied at the option of the vessel owner: (i) Under Article 3(2)(d) of the Convention: (A) For a U.S. flag vessel, this Article allows associated tonnage thresholds in effect on or before July 18, 1994 to be applied, at the vessel owner's option, using Regulatory Measurement System tonnage to a vessel whose keel was laid on or before July 18, 1982, and which did not subsequently undergo alterations resulting in a change in its tonnage of a magnitude deemed by the Commandant to constitute a substantial variation in its tonnage. (B) For a foreign flag vessel, this Article allows associated tonnage thresholds in effect on or before July 18, 1994, to be applied, at the vessel owner's option, using the foreign country's national measurement system tonnage to a vessel whose keel was laid on or before July 18, 1982, and which did not subsequently undergo alterations resulting in a change in its tonnage of a magnitude deemed by that country to constitute a substantial variation in its tonnage. (ii) Under International Maritime Organization (IMO) Resolutions A.494 (XII) of November 19, 1981 and A.541 (XIII) of November 17, 1983: (A) For a U.S. flag vessel, these resolutions allow tonnage thresholds in effect on July 18, 1994 to be applied using the gross register tonnage (Regulatory Measurement System), to a vessel whose keel was laid on or after July 18, 1982 but before July 19, 1994, and which did not subsequently undergo alterations resulting in a change substantially affecting its tonnage as deemed by the Commandant. (B) For a foreign flag vessel, these resolutions allow tonnage thresholds in effect on July 18, 1994 to be applied, at the vessel owner's option, using the foreign country's national measurement system tonnage, to a vessel whose keel was laid on or after July 18, 1982, but on or before July 18, 1994, and which did not undergo alterations after July 18, 1994 of a magnitude deemed by that country to constitute a substantial variation in its tonnage subject to the provisions of these resolutions. (iii) Any other international grandfathering provisions as authorized under appropriate International Maritime Organization instruments to which the United States is a party, or which are otherwise recognized or accepted by the United States. (2) For all other vessels, apply all tonnage thresholds using Regulatory Measurement System tonnage. (c) Thresholds found in Federal statutes and regulations. (1) For vessels measured under the Convention Measurement System only, apply all thresholds using Convention Measurement System tonnage. (2) For vessels measured under the Regulatory Measurement System only, apply all thresholds using Regulatory Measurement System tonnage. (3) For all other vessels, apply thresholds in effect before July 19, 1994 using the vessel's Regulatory Measurement System tonnage, and all other thresholds using the vessel's Convention Measurement System tonnage. (d) Alternate tonnage thresholds. (1) If an alternate tonnage threshold is prescribed or authorized by Federal statute or regulation, apply the alternate tonnage threshold using the Convention Measurement System tonnage. (2) A vessel regulated under paragraph (d) of this section must not be measured under the Regulatory Measurement System. [USCG-2011-0522, 81 FR 18720, Mar. 31, 2016] § 69.21 Right of appeal. Any person directly affected by a decision or action taken under this part, by or on behalf of the Coast Guard, may appeal therefrom in accordance with subpart 1.03 of this chapter. [CGD 88-033, 54 FR 50380, Dec. 6, 1989] § 69.23 Fees. Measurement organizations are authorized to charge a fee for measurement services. Information on fees is available directly from the organizations. [CGD 97-057, 62 FR 51045, Sept. 30, 1997] § 69.25 Penalties. (a) General violation. (b) False Statements. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18720, Mar. 31, 2016] § 69.27 Delegation of authority to measure vessels. (a) Under 46 U.S.C. 14103, the Coast Guard is authorized to delegate to a “qualified person” the authority to measure and certify U.S. flag vessels under this part. (b) Authority to measure and certify U.S. flag vessels under the Convention Measurement System and Standard and Dual Regulatory Measurement Systems may be delegated to an organization that— (1) Is a full member of the International Association of Classification Societies (IACS); (2) Is incorporated under the laws of the United States, a State of the United States, or the District of Columbia; (3) In lieu of the requirements in paragraphs (b)(1) and (2) of this section, is a recognized classification society under the requirements of 46 CFR part 8. (4) Is capable of providing all measurement services under the Convention Measurement System and Standard and Dual Regulatory Measurement Systems for vessels domestically and internationally; (5) Maintains a tonnage measurement staff that has practical experience in measuring U.S. flag vessels under the Convention Measurement System and Standard and Dual Regulatory Measurement Systems; and (6) Enters into a written agreement, as described in paragraph (d) of this section. (c) Applications for delegation of authority under this section must be forwarded to the Commandant and include the following information on the organization: (1) Its name and address. (2) Its organizational rules and structure. (3) The location of its offices that are available to provide measurement services under the Convention Measurement System and Standard and Dual Regulatory Measurement Systems. (4) The name, qualifications, experience, and job title of each full-time or part-time employee or independent contractor specifically designated by the organization to provide measurement services under theConvention Measurement System and Standard and Dual Regulatory Measurement Systems. (5) Its tonnage measurement training procedures. (d) If, after reviewing the application, the Coast Guard determines that the organization is qualified to measure and certify U.S. vessels on behalf of the Coast Guard, the organization must enter into a written agreement with the Coast Guard which— (1) Defines the procedures for administering and implementing the tonnage measurement and certification processes, including the roles and responsibilities of each party; (2) Outlines the Coast Guard's oversight role; (3) Prohibits the organization from using an employee or contractor of the organization to measure and certify the tonnage of a vessel if that employee or contractor is acting or has acted as a tonnage consultant for that same vessel; and (4) Requires the organization to— (i) Accept all requests to perform delegated services without discrimination and without regard to the vessel's location, unless prohibited from doing so under the laws of the United States or under the laws of the jurisdiction in which the vessel is located; (ii) Physically inspect each vessel before issuing a tonnage certificate; (iii) Provide the Coast Guard with current schedules of measurement fees and related charges; (iv) Maintain a tonnage measurement file for each U.S. vessel that the organization measures and permit access to the file by any person authorized by the Commandant; (v) Permit observer status representation by the Coast Guard at all formal discussions that may take place between the organization and other vessel tonnage measurement organizations pertaining to tonnage measurement of U.S. vessels or to the systems under which U.S. vessels are measured; (vi) Comply with and apply all laws and regulations relating to tonnage measurement of U.S. vessels within the scope of authority delegated; and (vii) Comply with all other provisions, if any, of the written agreement. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by CGD 97-057, 62 FR 51045, Sept. 30, 1997; CGD 95-010, 62 FR 67536, Dec. 24, 1997; USCG-2011-0522, 81 FR 18721, Mar. 31, 2016] § 69.28 Acceptance of measurement by a foreign country. (a) The Commandant must accept the measurement of a foreign flag vessel by a foreign country as complying with subpart B of this part if: (1) The vessel was measured under the terms of the Convention and the foreign country is party to the Convention; or (2) The Commandant finds that the laws and regulations of that country related to measurement are similar to those of subpart B of this part. (b) The Commandant may accept the measurement of a foreign flag vessel by a foreign country as complying with subpart C, D, or E of this part if the Commandant finds that the laws and regulations of that country related to measurement are substantially similar to those of subpart C, D, or E, respectively, of this part. [USCG-2011-0522, 81 FR 18721, Mar. 31, 2016] § 69.29 OMB control numbers assigned under the Paperwork Reduction Act. (a) Purpose. et seq. (b) Display Section of 46 CFR part 69 Currently assigned OMB control No. 69.17 1625-0022 69.19 1625-0022 69.21 1625-0022 69.27 1625-0022 69.55 1625-0022 69.105 1625-0022 69.121(d) 1625-0022 69.159 1625-0022 69.179 1625-0022 69.205 1625-0022 [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2004-18884, 69 FR 58346, Sept. 30, 2004] Subpart B—Convention Measurement System § 69.51 Purpose. This subpart prescribes the requirements for measuring a vessel in order to comply with the International Convention on Tonnage Measurement of Ships, 1969 (Convention), and 46 U.S.C. chapter 143. § 69.53 Definitions. As used in this subpart— Amidships Boundary bulkhead Cargo space Enclosed space Excluded space Line of the upper deck Molded depth (a) From the line of the upper deck at the vessel's side or, if the vessel has rounded gunwales, from the intersection of the line of the upper deck extended to the molded line of the shell plating as though the gunwales were of angular design. (b) To the top of the flat keel, to the lower edge of the keel rabbet if the vessel is of wood or composite structure, or to the point where the line of the flat of the bottom extended inward cuts the side of the keel if the vessel's lower part is hollow or has thick garboards. Molded draft (a) For vessels assigned a load line under parts 42, 44, 45, or 47 of this chapter, the draft corresponding to the Summer Load Line (other than a timber load line); (b) For passenger vessels assigned a load line under part 46 of this chapter, the draft corresponding to the deepest subdivision load line assigned; (c) For vessels to which parts 42, 44, 45, 46, or 47 of this chapter do not apply but which otherwise have been assigned a load line, the draft corresponding to the Summer Load Line so assigned; (d) For vessels to which no load line has been assigned but the draft of which is restricted under any Coast Guard requirement, the maximum draft permitted under the restriction; and (e) For other vessels, 75 per cent of the molded depth. Passenger (a) The master, a member of the crew, or other person employed or engaged in any capacity in the business of the vessel; and (b) A child under one year of age. Registered breadth Registered length Upper deck Weathertight [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18721, Mar. 31, 2016] § 69.55 Application for measurement services. Applications for measurement under this subpart must include the following information and plans: (a) Type of vessel. (b) Vessel's name and official number (if assigned). (c) Builder's name and the vessel hull number assigned by builder. (d) Place built and delivery date (or scheduled delivery date). (e) Date keel was laid. (f) Overall length, breadth, and depth of vessel. (g) Lines plan. (h) Booklet of offsets at stations. (i) Capacity plans for tanks and cargo compartments. (j) Hydrostatic curves. (k) Construction plans showing measurements and scantlings of deck structures, hatches, appendages, recesses, and other enclosed spaces. (l) Arrangement plans. [CGD 89-007; CGD 89-007a, 58 FR 60266, Nov. 15, 1993, 58 FR 65131, Dec. 13, 1993, as amended by CGD 95-014, 60 FR 31606, June 15, 1995; USCG-2011-0522, 81 FR 18721, Mar. 31, 2016] § 69.57 Gross tonnage ITC. Gross tonnage ITC (GT ITC) is determined by the following formula GT ITC = K 1 1 10 [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18721, Mar. 31, 2016] § 69.59 Enclosed spaces. Enclosed space [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18721, Mar. 31, 2016] § 69.61 Excluded spaces. (a) Excluded space (b) A space that is within a structure and that is opposite an end opening extending from deck to deck (except for a curtain plate of a height not exceeding by more than one inch the depth of the adjoining deck beams) and having a breadth equal to or greater than 90 percent of the breadth of the deck at the line of the opening is an excluded space, subject to the following: (1) Only the space between the actual end opening and a line drawn parallel to the line or face of the opening at a distance from the opening equal to one-half of the breadth of the deck at the line of the opening is excluded. (See § 69.75, figure 1.) (2) If, because of any arrangement (except convergence of the outside plating as shown in § 69.75, figure 3), the breadth of the space is less than 90 percent of the breadth of the deck, only the space between the line of the opening and a parallel line drawn through the point where the athwartship breadth of the space is equal to 90 percent or less of the breadth of the deck is excluded. (See § 69.75, figures 2 and 4.) (3) When any two spaces, either of which is excluded under paragraphs (b)(1) or (b)(2) of this section, are separated by an area that is completely open except for bulwarks or open rails, these two spaces must not be excluded if the separation between the two spaces is less than the least half breadth of the deck in way of the separation. (See § 69.75, figures 5 and 6.) (4) When the deck at the line of an opening has rounded gunwales, the breadth of the deck is the distance between the tangent points indicated in § 69.75, figure 11. (c) A space that is open to the weather and that is under an overhead deck covering with no connection on the space's exposed sides between the covering and the deck other than the stanchions necessary for the covering's support is an excluded space. An open rail or bulwark fitted at the vessel's side does not disqualify the space from being an excluded space if the height between the top of the rail or bulwark and the overhead structure or curtain plate (if fitted) is not less than 2.5 feet or one-third of the height of the space, whichever is greater. (See § 69.75, figure 7.) (d) A space in a side-to-side structure directly in way of opposite side openings not less than 2.5 feet in height or one-third of the height of the structure, whichever is greater, is an excluded space. If the opening is only on one side of the structure, the space to be excluded is limited inboard from the opening to a maximum of one-half of the breadth of the deck in way of the opening. (See § 69.75, figure 8.) (e) A space in a structure immediately below an uncovered opening in the deck overhead is an excluded space, if the opening is exposed to the weather and the space to be excluded is limited to the area of the opening. (See § 69.75, figure 9.) (f) A recess in the boundary bulkhead of a structure which is exposed to the weather and which has an opening that extends from deck to deck without a means of closing is an excluded space, if the interior width of the space is not greater than the width of the opening and extension of the space into the structure is not greater than twice the width of the opening. (See § 69.75, figure 10.) (g) Any space described in paragraphs (a) through (f) of this section which fulfills at least one of the following conditions is not an excluded space: (1) The space is fitted with shelves or other means designed for securing cargo or stores. (2) The opening that would otherwise permit the space to be excluded space is fitted with a means of closure. (3) Other features of the space make it possible for the space to be closed. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18721, Mar. 31, 2016] § 69.63 Net tonnage ITC. Net tonnage ITC (NT ITC) is determined by the formula: [USCG-2011-0522, 81 FR 18721, Mar. 31, 2016] § 69.65 Calculation of volumes. (a) Volumes V and V c (b) Measurements must be taken, regardless of the fitting of insulation or the like, to the inner side of the shell or structural boundary plating in vessels constructed of metal, and to the outer surface of the shell or to the inner side of structural boundary surfaces in all other vessels. [USCG-2011-0522, 81 FR 18722, Mar. 31, 2016] § 69.67 Marking of cargo spaces. Cargo spaces used in determining volume (Vc) for calculating net tonnage must be permanently marked with the letters “CC” (cargo compartment) which are at least four inches in height and positioned so as to be visible at all times. § 69.69 Tonnage certificates. (a) On request of the vessel owner, the authorized measurement organization must issue an International Tonnage Certificate (1969) as evidence of the vessel's measurement under this subpart for a vessel that is 24 meters (79.0 feet) or more in registered length, will engage on a foreign voyage, and is not a vessel of war. The Certificate is delivered to the vessel owner or master and must be maintained on board the vessel when it is engaged on a foreign voyage. For a vessel for which a remeasurement under § 69.71 resulted in a net tonnage ITC decrease due to changes other than alterations or modifications to the vessel deemed by the Commandant to be of a major character, an International Tonnage Certificate (1969) reflecting the decreased net tonnage ITC will not be reissued until 12 months have elapsed from the date of measurement indicated on the current certificate. (b) If an International Tonnage Certificate (1969) is not issued for a vessel measured under this part, the measurement organization must issue a U.S. Tonnage Certificate as evidence of the vessel's measurement under this subpart, which must also indicate the vessel's measurement under any other subpart of this part. There is no requirement to maintain the U.S. Tonnage Certificate on board the vessel. (c) For a vessel that transfers flag to a foreign country that is party to the Convention, the International Tonnage Certificate (1969) remains valid for a period not to exceed 3 months after the flag transfer, or until an International Tonnage Certificate (1969) is issued under authority of the foreign country to replace it, whichever is earlier. [USCG-2011-0522, 81 FR 18722, Mar. 31, 2016] § 69.71 Change of net tonnage. (a) When a vessel is altered so that the net tonnage is increased, the new net tonnage must be applied immediately. (b) A vessel concurrently assigned load lines under both the International Convention on Load Lines and either the International Convention for the Safety of Life at Sea (SOLAS) or other international agreement must be assigned only one net tonnage. The net tonnage assigned must be the net tonnage applicable to the load line assigned under the International Convention on Load Lines, SOLAS or other international agreement for the trade in which the vessel in engaged. (c) When a vessel is altered so that the net tonnage is decreased or the vessel's trade is changed so that the load line assigned for that trade under paragraph (b) of this section is no longer appropriate and results in a decrease in its net tonnage, a new International Tonnage Certificate (1969) incorporating that net tonnage may not be issued until twelve months after the date on which the current Certificate was issued. However, if one of the following apply, a new Certificate may be issued immediately: (1) The vessel is transferred to the flag of another nation. (2) The vessel undergoes alterations or modifications which the Commandant deems to be of a major character, such as the removal of a superstructure which requires an alteration of the assigned load line. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-1999-6216, 64 FR 53225, Oct. 1, 1999; USCG-2011-0522, 81 FR 18722, Mar. 31, 2016] § 69.73 Treatment of novel type vessels. (a) When application of this subpart to a novel type vessel produces unreasonable or impractical results, the Commandant may determine a more suitable method of measurement. (b) Requests for a determination must be submitted to the Commandant, explaining the reasons for seeking a determination, and including a description of the spaces in question, if applicable. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by CGD 97-057, 62 FR 51045, Sept. 30, 1997; USCG-1999-6216, 64 FR 53225, Oct. 1, 1999; USCG-2011-0522, 81 FR 18722, Mar. 31, 2016] § 69.75 Figures. [USCG-2011-0522, 81 FR 18722, Mar. 31, 2016] Subpart C—Standard Regulatory Measurement System § 69.101 Purpose. This subpart prescribes the procedures for measuring a vessel under the Standard Regulatory Measurement System described in 46 U.S.C. 14512. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18724, Mar. 31, 2016] § 69.103 Definitions. As used in this subpart— Between-deck Break Camber Ceiling Coaming Deckhouse Depth of frame Double bottom Double bottom for water ballast Floor Gross register tonnage Hatch Line of the normal frames Line of the ordinary frames Line of tonnage deck Line of uppermost complete deck Net register tonnage Normal frame Ordinary frame Registered breadth Registered depth Registered length Shelter deck Step Superstructure Tonnage deck Tonnage interval Tonnage length Tonnage station Uppermost complete deck Zone of influence method [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18724, Mar. 31, 2016] § 69.105 Application for measurement services. Applications for measurement services under this subpart must include the following information and plans: (a) Type of vessel. (b) Vessel's name and official number (if assigned). (c) Builder's name and the vessel hull number assigned by the builder. (d) Place built and delivery date (or scheduled delivery date). (e) Date keel was laid. (f) Overall length, breadth, and depth of vessel. (g) Lines plan. (h) Booklet of offsets. (i) Capacity plans for tanks (j) Construction plans showing measurements and scantlings of hull and superstructure. (k) Tonnage drawing showing tonnage length in profile and tonnage sections. (l) Arrangement plans. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by CGD 95-014, 60 FR 31606, June 15, 1995; USCG-2011-0522, 81 FR 18725, Mar. 31, 2016] § 69.107 Gross and net register tonnage. (a) The vessel's gross register tonnage is the sum of the following tonnages, less the tonnages of certain spaces exempt under § 69.117: (1) Under-deck tonnage (§ 69.109). (2) Between-deck tonnage (§ 69.111). (3) Superstructure tonnage (§ 69.113). (4) Excess hatchway tonnage (§ 69.115(c)). (5) Tonnage of framed-in propelling machinery spaces included in calculating gross tonnage (§ 69.121(d)(1)). (b) The vessel's net register tonnage is the gross register tonnage less deductions under §§ 69.119 and 69.121. (c) The authorized measurement organization must issue a U.S. Tonnage Certificate as evidence of a vessel's measurement under this subpart, which must also indicate the vessel's measurement under the Convention Measurement System in subpart B of this part, if applicable. There is no requirement to maintain the U.S. Tonnage Certificate on board the vessel. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18725, Mar. 31, 2016] § 69.108 Uppermost complete deck. (a) Defined. (b) Restrictions. (1) Extend above any space exempted as open space under paragraph (d) of § 69.117; (2) Extend below the design waterline, except in the case of vessels such as submersibles, where the entire uppermost complete deck is submerged during normal operations; or (3) Rest directly on consecutive or alternating ordinary bottom frames or floors for a distance of over one-half of the tonnage length. (c) Deck discontinuities. (1) Through-deck openings that are not protected from the sea and the weather, such as would be provided by hatch covers or a surrounding superstructure that encloses the opening and whose area is more than 10 percent of the total deck area from stem to stern as viewed from above. (2) Middle line openings conforming to the requirements of § 69.117(e)(2). (3) Deck recesses that are not through-hull for which the depth of the deck recess at its deepest point is more than five feet below adjacent portions of the deck, and whose area (as viewed from above) is more than 10 percent of the total deck area from stem to stern, as viewed from above. (4) Notches bounded by a deck below that wrap around from the ends to the sides of the vessel for which the depth at the deepest point is more than five feet below adjacent portions of the deck, the area is more than one percent of the total deck area from stem to stern as viewed from above, the length of the notch in the direction of the vessel's longitudinal axis exceeds 10 feet at any point across its width, and the width of the notch in the direction of the vessel's longitudinal axis exceeds two feet at any point along its length. [USCG-2011-0522, 81 FR 18725, Mar. 31, 2016] § 69.109 Under-deck tonnage. (a) Defined. (b) Method of calculating tonnage. (c) Identifying the tonnage deck. (d) Enumerating the decks to identify the second deck from the keel. (1) A through-deck opening that is not fitted with a cover (or equivalent) and whose area is more than 10 percent of the total deck area, as viewed from above. (2) A deck recess that is not through-hull for which the depth at its deepest point is more than five feet below adjacent portions of the deck and whose area as viewed from above is more than 10 percent of the total deck area from stem to stern, as viewed from above. (e) Identifying the line of the tonnage deck. (2) If the tonnage deck is stepped, the line of the tonnage deck is the longitudinal line of the underside of the lowest portion of that deck parallel with the upper portions of that deck. Steps that do not extend from side to side or are less than three feet in length are ignored when establishing the line of the tonnage deck. (See § 69.123, figures 1 and 2.) Spaces between the line of the tonnage deck and the higher portions of that deck are not included in under-deck tonnage. (f) Tonnage length. (2) For a vessel having a headblock or square end with framing which extends from the tonnage deck to the bottom of the vessel, the tonnage length terminates on the inboard face of the headblock or ordinary end frames. (See § 69.123, figure 4.) (3) For a vessel having a square bow or stern and tonnage deck with camber, the effect of the camber on the tonnage length must be considered. The tonnage length must be measured below the tonnage deck at a distance equal to one-third of round camber and one-half of straight pitch camber. (4) The forward and after termini of the tonnage length must be a distance of no more than eight and one-half feet from the associated inboard surface of the skin of the hull at the bow and stern as measured at the centerline of the vessel, and the after terminus must not be forward of the centerline of the rudderstock. (g) Division of vessel into transverse sections. Class Tonnage length Divisions 1 50 ft. or less 6 2 Over 50 ft. but not exceeding 100 ft 8 3 Over 100 ft. but not exceeding 150 ft 10 4 Over 150 ft. but not exceeding 200 ft 12 5 Over 200 ft. but not exceeding 250 ft 14 6 Over 250 ft. 16 (2) Transverse sections are cut at each end of the tonnage length and at each point of division of the tonnage length, whose location is referred to as a tonnage station, and assigned sequential tonnage station numbers, beginning at the stem. Intervals and one-third intervals between the points of division are measured to the nearest thousandth of a foot. (See § 69.123 figures 5 and 6.) (h) Depths of transverse sections. (2) When a depth falls at a point where the tank top of a double bottom for water ballast has a straight fall from centerline to the wings, the depth terminates at one-half of the height of fall. (See § 69.123 figure 8.) (3) When a depth falls at a point where the tank top of a double bottom for water ballast rises from the centerline to the wings, the depth terminates at one-half the dead rise. (See § 69.123, figure 9.) (4) The depth at the midpoint of the tonnage length or, when a vessel is measured in parts, the depth at the midpoint of each part determines the number of equal parts into which each depth is divided, as follows: (i) If the midpoint depth is 16 feet or less, each depth is divided into four equal parts. If the midpoint depth exceeds 16 feet, each depth is divided into six equal parts. (See § 69.123, figure 7.) (ii) The interval between the points of division of a depth and one-third intervals are carried to the nearest hundredth of a foot. (i) Breadths of transverse sections. (2) Upper breadths are not reduced by measuring to deck-beam brackets. In cases of camber when an upper breadth passes through the deck (see § 69.123, figure 7), the breadth is measured to the line of the side frames at the under side of the deck projected vertically up to the height of the upper breadth. (3) Bottom breadths are measured only as far as the flat of the floor extends. (See § 69.123, figures 7 and 10.) When bottom frames rise immediately from the flat keel, bottom breadths are equal to the breadth of the flat keel. Where there is no double bottom for water ballast and where there is dead rise of the bottom out to the sides of the vessel, bottom breadths are equal to the part of the bottom plating not affected by dead rise. (4) Bottom breadths falling in way of a double bottom, the top of which rises or falls from centerline to the wings, are measured between the inboard faces of the frame brackets which connect the double bottom with the frames. (See § 69.123, figures 8 and 9.) (j) Measuring spaces having ceiling. (k) Area of transverse sections. (2) The breadths of each transverse section are numbered from above, the upper being “1”, the second down being “2”, and so on to the lowest. (3) Multiply the even numbered breadths by four and the odd numbered breadths by two, except for the first and last breadths, which are multiplied by one. (4) Add together the products from paragraph (k)(3) of this section. (5) Multiply the sum from paragraph (k)(4) of this section by one-third of the interval between the breadths. The product is the area of the transverse section. (l) Tonnage. (2) Multiply the area of the even numbered sections by four and the area of the odd numbered sections by two, except the first and last sections, which are multiplied by one. (3) Add together the products from paragraph (l)(2) of this section and multiply the sum by one-third of the interval between the sections. The product is the volume under-deck. (4) The volume under-deck is divided by 100 and is, subject to exemptions, the under-deck tonnage. (m) Steps in double bottom for water ballast. (i) Parts 20 feet or under in length are divided into two equal parts. (ii) Parts over 20 feet and under 40 feet in length are divided into four equal parts. (iii) Parts 40 feet or over are divided as provided in paragraph (g)(1) of this section. (2) The tonnage of each part is calculated separately. The sum of the tonnages of the parts is the under-deck tonnage. (n) Spaces open to the sea. (o) Open vessels. (2) The line of the tonnage deck for an open vessel is the upper edge of the upper strake. Depths of transverse sections are taken from this line. (3) Any vessel, other than one having a mechanically refrigerated hold, that is not an open vessel and that has a tonnage length of less than 50 feet is measured as an open vessel, if the distance between the line of its tonnage deck and the upper edge of the upper strake is more than one-sixth of the midship depth. “Midship depth” means the depth measured from the line of the upper edge of the upper strake to the point in the bottom used for measuring tonnage depths. (p) General requirements on ordinary frames Construction. (2) Frame spacing and extension. (3) Different sized framing. (4) Frame openings. (i) Circular in shape with a diameter exceeding 18 inches; (ii) Oval in shape of a size greater than 15 × 23 inches ( i.e., (iii) Any shape other than circular or oval, whose area exceeds 255 square inches (345 square inches in a fuel tank). (5) Asymmetrical framing. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989; 54 FR 40240, Sept. 29, 1989; USCG-2014-0688, 79 FR 58281, Sept. 29, 2014; USCG-2011-0522, 81 FR 18725, Mar. 31, 2016] § 69.111 Between-deck tonnage. (a) Defined. (b) Identifying the line of the uppermost complete deck. (2) If the uppermost complete deck is stepped, the line of the uppermost complete deck is the longitudinal line of the underside of the lowest portion of that deck parallel with the upper portions of that deck. Steps that do not extend from side to side or are less than three feet in length are ignored when establishing the line of the uppermost complete deck. Spaces between the line of the uppermost complete deck and the higher portions of the deck are included in superstructure tonnage. (c) Method for calculating tonnage. (1) The length of each level is measured at the mid-height between the line of the deck above and the line of the deck below. Measure from the point forward where the continuation of the line of the normal frames intersects the center line of the vessel aft to the forward face of the normal transom framing. (2) Divide the length under paragraph (c)(1) of this section into the same number of equal parts into which the tonnage length is divided under § 69.109(g)(1). (3) Measure at mid-height the inside breadth of the space to the line of the normal frames at each end and at each point of division of the length. Number the breadths successively “1”, “2”, and so forth beginning at the bow. (4) Multiply the even numbered breadths by four and the odd numbered breadths by two, except the first and last, which are multiplied by one. (5) Add together the products under paragraph (c)(4) of this section and multiply the sum by one-third of the interval between the points at which the breadths are taken. The product is the square foot area of the space at mid-height. (6) Multiply the area of the space at mid-height by the average of the heights taken each point of division of the space. The product divided by 100 is the tonnage of that space. (7) The between-deck tonnage is the sum of the tonnage of each level within the between-deck space. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by CGD 97-057, 62 FR 51045, Sept. 30, 1997; USCG-2011-0522, 81 FR 18726, Mar. 31, 2016] § 69.113 Superstructure tonnage. (a) Defined. (b) Method of calculating tonnage. (1) Measure the length of each structure along its centerline at mid-height to the line of the normal frames. (See § 69.123, figure 11.) (2) Divide the length under paragraph (b)(1) of this section into an even number of equal parts most nearly equal to those into which the tonnage length is divided under § 69.109. (3) Measure at mid-height the inside breadth to the line of the normal frames at each end and at each point of division of the length. Number the breadths successively “1”, “2”, and so forth, beginning at the extreme forward end of the structure. If an end of the structure is in the form of a continuous arc or curve, the breadth at that end is one-half the nearest breadth. If an end is in the form of an arc or curve having a decided flat, the breadth at the end is two-thirds of the nearest breadth. (4) Multiply the even numbered breadths by four and the odd numbered by two, except the first and last breadth, which are multiplied by one. (5) Add together the products under paragraph (b)(4) of this section and multiply the sum by one-third of the interval between the points at which the breadths are taken. The product is the square foot area of the structure at mid-height. (6) Multiply this area by the average of the heights taken at each point of division of the structure between its decks or the line of its decks. The product divided by 100 is the tonnage of that structure. (c) A structure having steps in its deck or side must be measured in parts. (d) The superstructure tonnage is the sum of tonnages of each level above the line of the uppermost complete deck (or shelter deck, if applicable). (e) When a structure is located over a cut-away portion of the tonnage deck, the structure's height is measured from the under side of its overhead deck to the line of the tonnage deck. If the tonnage deck has no camber, allow for camber in the overhead deck. (f) For structures of a standard geometric shape, a simple geometric formula that yields an accurate volume may be used. All measurements are terminated at the line of the normal frames. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2014-0688, 79 FR 58281, Sept. 29, 2014; USCG-2011-0522, 81 FR 18726, Mar. 31, 2016] § 69.115 Excess hatchway tonnage. (a) Hatchways that are above the tonnage deck and are either open to the weather or within open structures are measured to determine excess hatchway tonnage. Hatchways that are in between-deck spaces, on decks within closed-in structures, or on open structures are not measured. (b) The tonnage of a hatchway is its length times breadth times mean depth divided by 100. Mean depth is measured from the under side of the hatch cover to the top of the deck beam. (c) From the sum of the tonnage of the hatchways under this section, subtract one-half of one percent of the vessel's gross register tonnage exclusive of the hatchway tonnage. The remainder is added as excess hatchway tonnage in calculating the gross register tonnage. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18727, Mar. 31, 2016] § 69.117 Spaces exempt from inclusion in tonnage. (a) Purpose. (b) Spaces on or above the line of the uppermost complete deck. (1) Spaces for anchor gear, including capstan, windlass, and chain locker, are exempt. (2) Companions and booby-hatches protecting stairways or ladderways leading to spaces below are exempt, whether or not the spaces below are exempt. (3) Galley or other spaces fitted with a range or oven for cooking food to be consumed on board the vessel are exempt. (4) Spaces designed to provide light or air to propelling machinery are exempt, as follows: (i) When propelling machinery is located entirely on or above the line of the uppermost complete deck, the entire propelling machinery space and all fuel bunker spaces that are also located above that line are exempt as light or air spaces. (See exception in § 69.121(d)(1) for framed-in spaces.) (ii) When part of the propelling machinery projects above the line of the uppermost complete deck into a space used exclusively to provide light or air to the propelling machinery, the entire space is exempt as light or air space. When any portion of this space is used for purposes other than providing light or air, only the portion of the space used for light or air, the space occupied by the propelling machinery itself, and a propelling machinery working space allowance under § 69.121 limited to two feet, if available, on each side of the propelling machinery are exempt. (iii) Any part of an escape shaft, or a companion sheltering an escape shaft, above the line of the uppermost complete deck is exempt as light or air space. (iv) Space that would otherwise be exempt as a light or air space is not exempt when propelling machinery is boxed-in and does not extend above the line of the uppermost complete deck. Any portion of the boxed-in space above the line of the uppermost complete deck is exempt. (5) Skylights affording light or air to a space below, other than to propelling machinery spaces. Space immediately below the line of the deck on which a skylight is located is exempt only when there is an opening in the next lower deck directly below the skylight to permit light or air to an even lower deck. (6) Machinery spaces, other than for propelling machinery under § 169.121. (7) Spaces for steering gear. (8) Water closet spaces that are fitted with at least a toilet and are intended for use by more than one person. (9) The space in a wheelhouse necessary for controlling the vessel. (c) Passenger spaces. (2) As used in this section, “passenger space” means a space reserved exclusively for the use of passengers and includes, but is not limited to, berthing areas, staterooms, bathrooms, toilets, libraries, writing rooms, lounges, dining rooms, saloons, smoking rooms, and recreational rooms. The space need not be part of or adjacent to a berthing area to be considered a passenger space. Spaces used by both passengers and crew members (e.g., first aid stations), or used for passenger support but not accessible to passengers at all times (e.g., vaults on a gaming vessel) cannot be exempted as passenger space. (3) A passenger space located on, or above the first deck above the uppermost complete deck is exempt from tonnage. To qualify as the first deck above the uppermost complete deck, the deck must be at least six inches above the uppermost complete deck at all points along its length. (d) Open structures. (i) If a structure is divided into compartments, only those compartments which are open to the weather are exempt from tonnage under the provisions of this section. (ii) Open space cannot progress vertically through openings in a deck within the structure. (iii) A space that is outside a structure's boundary bulkhead as defined in § 69.53 is considered open to the weather provided the space is eligible to be treated as an excluded space under the provisions of § 69.61, regardless of whether or not the space is fitted with means designed for securing cargo or stores. (2) A structure is considered open to the weather when an exterior end bulkhead of the structure is open and, except as provided in paragraphs (d)(4), (5), and (6) of this section, is not fitted with any means of closing. To be considered open to the weather, the end bulkhead must not have a coaming height of more than two feet in way of any required opening nor any permanent obstruction within two and one-half feet of the opening, it must be fitted with a deck or platform that is a minimum of two and one-half feet wide on the exterior side of the opening, and it must have one of the following: (i) Two openings, each at least three feet wide and at least four feet high in the clear, one on each side of the centerline of the structure. If the openings lead to two separate interior compartments, there must be circulation of open space between the two compartments via a single such opening, or series of such openings, in the intermediate bulkhead(s). (ii) One opening at least four feet wide and at least five feet high in the clear. (iii) One opening at least 20 square feet in the clear with a breadth in excess of four feet and a height of not less than three feet. (3) A compartment within an open structure is considered open to the weather only when an interior bulkhead of that compartment has an opening or openings that meet the requirements for end bulkheads under paragraphs (d)(2)(i) and (iii) of this section. Other compartments within the structure are not considered open to the weather. The following additional requirements apply: (i) For the interior compartment to be considered open to the weather, any compartment or series of compartments from which the open space progresses must have an opening or openings meeting the requirements for end bulkhead openings, except that the opening(s) need not be located in the forward or after end of the compartment. (ii) Open space may not progress from a space that is open under the provisions of paragraph (d)(1)(iii) of this section unless the space may also be considered open under another provision of this section. (4) An interior or exterior opening that is temporarily closed by shifting boards dropped into channel sections at the sides of the opening is considered open to the weather if battening, caulking, or gaskets of any material are not used. (5) An interior or exterior opening that is temporarily closed by cover plates or boards held in place only by hook bolts (see § 69.123, Figure 12) is considered open to the weather— (i) If hook bolts used to secure cover plates or boards are spaced at least one foot apart and hook over a stiffener installed around the perimeter of the opening; (ii) If the cover plates or boards fit tightly against the weather side of the bulkhead; and (iii) If battening, caulking, or gaskets of any material are not used. (6) An interior or exterior opening that is temporarily closed by cover plates or boards held in place only by bolts and crosspieces is considered open to the weather— (i) If the bolts are not installed through the bulkhead; (ii) If the bolts and crosspieces are not held in place by cleats or other attachments to or through the bulkhead; (iii) If the cover plates or boards fit tightly against the weather side of the bulkhead; and (iv) If battening, caulking, or gaskets of any material are not used. (7) Notwithstanding the opening size requirements of paragraph (d)(2) of this section, a structure with its aft end entirely open from the under side of its overhead stiffeners down to the deck, to the line of the deck, or to a coaming not exceeding three inches in height and open athwartship between the inboard faces of the side stiffeners is considered open to the weather. The opening may be covered by a wire mesh screen or temporarily closed by canvas secured at the top and lashed or buttoned in place. (8) A structure is considered open to the weather if: (i) Both sides of the structure are open and not fitted with any means of closing other than temporary covers meeting the requirements of paragraphs (d)(4), (5), and (6) of this section; (ii) The openings are directly across from each other, are not separated by a bulkhead or bulkheads, and do not have any permanent obstruction within two and one-half feet of either opening; and (iii) The openings have a continuous height of at least three feet, or the full height of the structure, whichever is less, and either extend the full length of the structure or each have an area of 60 square feet. (e) Open space between the shelter deck and the uppermost complete deck. (2) A space is considered “open to the weather” under paragraph (e)(1) of this section when the shelter deck above the space has a middle line opening which conforms to the following: (i) The middle line opening must be at least four feet long in the clear and at least as wide as the after cargo hatch on the shelter deck, but not less than one-half the width of the vessel at the midpoint of the length of the opening. The opening may have rounded corners not exceeding a nine inch radius. When a greater radius is required by the Coast Guard or a Coast Guard recognized classification society under § 42.05-60 of this chapter, notification of that requirement must be submitted to the Commandant. (ii) The middle line opening must be located so that the distance between the aft edge of the middle line opening and the vessel's stern is not less than one-twentieth of the tonnage length of the vessel and the distance between the fore edge of the opening and the vessel's stem is not less than one-fifth of the tonnage length of the vessel. (iii) The middle line opening must not be within a structure of any type. (iv) If the middle line opening is guarded by rails or stanchions, the rails and stanchions must not be used to secure or assist in securing a cover over the opening. (v) The coaming of the middle line opening must not exceed one foot mean height above the shelter deck. Bolts must not pass through the stiffeners or flanges on the coaming, nor may there be any other attachments on the coaming for fastening a cover. Portable wood covers may be fitted over the middle line opening if held in place only by lashings fitted to the under side of the covers. Metal covers may be fitted if held in place only by hook bolts spaced not less than 18 inches apart that pass through the cover and hook over angle stiffeners or flanges fitted to the outside of the coaming. Battening, caulking, seals, or gaskets of any material may not be used in association with any middle line opening cover. (vi) The space below the middle line opening must have a minimum length of four feet throughout its entire breadth and height and be in the clear at all times. (vii) A scupper having a five inch minimum inside diameter and fitted with a screw down non-return valve geared to and operated from the shelter deck must be fitted on each side of the upper deck in way of the middle line opening. (3) When the shelter deck space forward or aft of the middle line opening is divided by interior bulkheads, only those compartments with at least two openings that progress to the middle line opening are considered “open to the weather” under paragraph (e)(1) of this section. Each required opening must be at least three feet wide and at least four feet high in the clear, must not have a coaming height of more than two feet, and must not be fitted (except as provided in paragraphs (d)(4), (d)(5), and (d)(6) of this section) with any means of closing. Other compartments within the shelter deck space are not considered “open to the weather” under paragraph (e)(1) of this section. (f) Water ballast spaces. (1) The space must be available at all times only for water ballast that is piped through a system independent of other systems (except fire fighting and bilge suction systems). Pumps, pipes, and other equipment for loading and unloading water ballast must be of a size suitable for the efficient handling of the water ballast within a reasonable time frame. All manholes providing access to a water ballast space must be oval or circular and not greater than 34 inches in diameter. Except for those on a deck exposed to the weather, the manholes may have a coaming not exceeding six inches in height. Existing hatches over spaces being converted to water ballast spaces must have a watertight cover plate welded to the hatch and a manhole, as described in this paragraph, fitted in the plating. (2) The primary purpose of the water ballast must be to afford a means of maintaining the vessel's stability, immersion, trim, pre-loading conditions, or seakeeping capabilities. (3) If the space is in a vessel that is subject to inspection under 46 U.S.C. 3301, the space must be considered when determining the adequacy of the vessel's stability under 46 CFR chapter I. (4) If the total of all water ballast spaces to be exempted from tonnage exceeds 30 percent of the vessel's gross register tonnage (as calculated under this subpart without any allowance for water ballast), a justification of the operating conditions that require the water ballast must be submitted to the measuring organization for approval. Although a single condition may justify all water ballast spaces, several conditions may be necessary in other cases. However, a particular tank is not justified by a condition if another tank already justified by another condition could be used as effectively. The justification must— (i) Designate the vessel's service; (ii) Explain for what purpose under paragraph (f)(2) of this section the water ballast is being used; (iii) Include the capacity, tank arrangement, and piping plans for the vessel; (iv) Include a statement certifying that the space will be used exclusively for water ballast as prescribed by this section; (v) If water ballast is used for stability, describe each loading condition and the resultant metacentric height (GM) and include calculations; (vi) If water ballast is used for immersion or trim, describe those conditions and include loading and trim calculations; (vii) If water ballast is used for pre-loading, describe how it is used and include strength and weight calculations; and (viii) If water ballast is used for seakeeping, describe each loading condition, GM, period of roll, and, if speed is involved, speed versus trim and draft and include calculations. (5) If the water ballast space or its use, purpose, or piping are changed, the vessel owner or operator must report the change promptly to a measurement organization listed in § 69.15 for a determination as to whether a tonnage remeasurement is required.

Changes in vessel service must also be reported if a water ballast justification was required to be submitted for the vessel. (g) Methods for measuring exempt spaces. (2) If the exempt space is located between-deck, the space is measured using the same procedures used for between-deck tonnage under § 69.111(c), except that the length of the exempt space is divided into the even number of spaces most equal to the number of spaces into which the between-deck was divided. (3) If the exempt space is located under-deck, the space is measured using the same procedures used for under-deck tonnage under § 69.109, except that the length of the exempt space is divided into the even number of spaces most equal to the number of spaces into which the under-deck was divided, and the zone of influence method must be applied if the ordinary frames upon which the under-deck breadth measurements are based do not have the same depth of frame. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989; 54 FR 40240, Sept. 29, 1989; CGD 97-057, 62 FR 51045, Sept. 30, 1997; CGD 95-028, 62 FR 51203, Sept. 30, 1997; USCG-1999-5118, 64 FR 47404, Aug. 31, 1999; USCG-2011-0522, 81 FR 18727, Mar. 31, 2016] § 69.119 Spaces deducted from tonnage. (a) Purpose. i.e., (b) General. (2) When a space is larger than necessary for the safe and efficient operation of deductible equipment, only the space occupied by the equipment plus a two foot maximum working space on each side of the equipment, if available, is deductible. (3) Space specified in this section may be located anywhere within the vessel, unless otherwise specified. (c) Anchor gear. (d) Boatswain's stores. (e) Chart room. (f) Donkey engine and boiler. (1) If the space is within the engine room or within the casing above the engine room and if the donkey engine is an auxiliary to the main propelling machinery, the space is an engine room deduction under § 69.121(b). (2) If the space is above the line of the uppermost complete deck and if the donkey engine is not an auxiliary to the main propelling machinery, the space is exempt under § 69.117(b). (g) Spaces for the exclusive use of officers or crew. (i) Sleeping rooms. (ii) Bathrooms with a bath tub or shower but without a water closet. (iii) Water closets below the line of the uppermost complete deck serving more than one person, with or without a bath tub or shower. Water closets, regardless of location, that serve only one person or that are accessible only through a stateroom or bedroom serving one person are considered as part of the space they serve and are deductible only if that space is deductible. (iv) Clothes drying rooms. (v) Drinking water filtration or distilling plant below the line of the uppermost complete deck. (vi) Hospitals. (vii) Mess rooms. (viii) Office of the chief engineer. (ix) Oil skin lockers. (x) Pantries. (xi) Recreation rooms. (xii) Smoking rooms. (xiii) Galleys below the line of the uppermost complete deck. (2) Shops for engineers, carpenters, plumbers, or butchers and offices for clerks, pursers, or postmasters are not deductible, wherever located. (h) Master's cabin. (i) Radio room. (j) Steering gear. (k) Generators. (l) Pump room. (m) Sail stowage. (n) Waste material space. (2) Space below the line of the uppermost complete deck used exclusively to separate, clarify, purify, or otherwise process waste material generated aboard the vessel is deductible. (o) Passageways. (1) If it serves deductible spaces only; or (2) If it serves deductible spaces and is also the sole means of access to one of the following non-deductible spaces: (i) Lockers of less than two tons each, containing medicine, linen, mops, or other items for the free use of the crew. (ii) A ship's office. (iii) Spare rooms (not exceeding two) used by a pilot, customs officer, reserve engineer, or employee or agent of the vessel's owner or operator. (p) Markings for deductible spaces. (2) The abbreviations “Cert.” for “certified” and “W.C.” for “water closet” may be used. (3) The markings must be in Roman letters and Arabic numerals at least 1/2 (q) Method for measuring deductible spaces. (2) A space with curved sides on or above the tonnage deck is measured according to § 69.109. (3) Space less than 15 feet in length may be measured by any practical method. (4) Spaces below the tonnage deck exceeding 15 feet in length and bounded by a curved surface conforming to the side of the vessel must be measured by the formula used for measuring the superstructure under § 69.113. (5) The height of a space located on a platform in the hull must be measured from the top of the bottom hull frames, if the platform is used only to form a flat surface at the bottom of the space, if the platform is not more than one foot above the top of the bottom frames, and if the space below the platform is not usable. (6) The height of a space is measured through any ceiling, paneling, false overhead, or other covering, to the space's structural boundary, unless the space enclosed by the covering is available for a non-deductible use. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989; 54 FR 40240, Sept. 29, 1989; CGD 92-058, 57 FR 59938, Dec. 17, 1992; USCG-2011-0522, 81 FR 18727, Mar. 31, 2016] § 69.121 Engine room deduction. (a) General. (b) Propelling machinery spaces. (2) Propelling machinery spaces are— (i) Space below the crown. The crown is the top of the main space of the engine room to which the heights of the main space are taken. The crown is either the underside of a deck or, if the side bulkheads are sloping, the uppermost point at which the slope terminates. (See § 69.123, figures 13 and 14.) (ii) Framed-in space located between the crown and the uppermost complete deck and used for propelling machinery or for the admission of light or air to propelling machinery spaces. (See § 69.123, figures 13 and 14.) (iii) Shaft tunnel space and thrust block recess space. (iv) Space below the uppermost complete deck used for escape shafts or trunked ladderways leading from the aft end of the shaft tunnel to the deck above. (v) Space containing a fuel oil transfer pump located in a separate space and not used for bunkering the vessel. When the pump serves both ballast and fuel oil, only one-half of the pump's space is considered a propelling machinery space. (vi) Spaces containing fuel oil settling tanks used solely for the main boilers. The space must not exceed one percent of the vessel's gross tonnage. (vii) Spaces for engineers' stores and workshops located below the uppermost complete deck and either open to a propelling machinery space or separated from a propelling machinery space only by a screen bulkhead. The space must not exceed three-quarters of one percent of the vessel's gross register tonnage. (viii) Framed-in space located above the line of the uppermost complete deck and used for propelling machinery or for the admission of light or air to a propelling machinery space, when requested under paragraph (d) of this section. (ix) If the propelling machinery is boxed-in below the tonnage deck, the boxed-in space plus the spaces outside of the boxing for the shaft, auxiliary engines, and related propelling machinery. If a portion of the boxed-in space extends above a platform or partial deck that is below the uppermost complete deck, that portion is also considered part of the propelling machinery space. (c) Methods for measuring propelling machinery spaces. (2) If the propelling machinery space is not bulkheaded off or is larger than necessary for the safe operation and maintenance of the propelling machinery, only the space occupied by the propelling machinery itself plus a working space of two feet, if available, on each side of the propelling machinery is measured for the engine room deduction. If the working space overlaps another working space not related to the propelling machinery, only one-half of the overlapping working space is included in the propelling machinery space. The height of the working space is measured as provided in paragraph (c) of this section. (3) If the propelling machinery is located in more than one space, each space must be measured separately. (4) If the propelling machinery is located in a space with a step in the bottom or side lines, each stepped portion of the space must be measured separately. (5) The length of a space under paragraph (c)(1) of this section is measured from the bulkhead just forward of the propelling machinery to the bulkhead just aft of the propelling machinery. The length of a space under paragraph (c)(2) of this section is measured from the forward edge of the working space to the aft edge of the working space. (6) If the boundaries of the propelling machinery space form a rectangle, the product of the length, breadth, and height, divided by 100, is the tonnage of the space. (7) If the boundaries of the propelling machinery space are continuous fair lines, heights are measured at the fore and aft ends and at the center of the space from the bottom frames, floors, or tank top of a double bottom up to the line of the crown. A breadth is measured at half-height of each height. The product of the length, mean breadth, and mean height, divided by 100, is the tonnage of the space. (8) If the propelling machinery space is in the aft end of the hull, extends from side to side of the hull, and has a continuous bottom line, the length of the space is divided into the even number of equal parts most nearly equal to the number of parts that the tonnage length under § 69.109(g) was divided. The tonnage is then calculated by the same method used for calculating the under-deck tonnage in § 69.109(l). (9) The tonnage of a framed-in space located between the crown and the uppermost complete deck and used for propelling machinery or for the admission of light or air to the propelling machinery space, is the product of its length, breadth, and height, divided by 100. (10) The tonnage of a shaft tunnel, or a thrust block recess, having a flat top is the product of its length, breadth, and height, divided by 100. If the shaft tunnel or thrust block recess top is not flat, the space above must be calculated by using the appropriate geometrical formula. If the space aft of the shaft tunnel extends from side to side of the vessel, the tonnage of the space is found by the formula for measuring peak tanks in § 69.109(l). (11) The length and breadth of the space for a shaft tunnel, or a thrust block recess, when not cased is that which is necessary for maintenance of the shaft. The height allowed for thrust block recess space must not exceed seven feet. The mean height allowed for the shaft tunnel space must not exceed six feet. In a multi-screw vessel where the shaft tunnel or thrust block recess space is open from side to side, measure only the space used for purposes of propelling the vessel. (12) When the propelling machinery is on a bed at the vessel's bottom, the height of the propelling machinery space is measured from the top of the bottom frames or floors. (d) Request to treat certain framed-in engine room spaces as part of a propelling machinery space. (2) The framed-in space must be safe, seaworthy, and used only for propelling machinery or for the admission of light or air to the propelling machinery space. The length of the space must not exceed the length of the propelling machinery space and the breadth must not exceed one-half of the extreme inside midship breadth of the vessel. Portions of the framed-in space that are plated over are not included in the propelling machinery space. (3) To exercise the option in paragraph (d)(1) of this section, all of the framed-in space need not be treated as propelling machinery space, but only that portion required to entitle the vessel to have 32 percent of its gross register tonnage deducted as an engine room deduction under paragraph (e) of this section. (e) Calculating the engine room deduction. (2) For vessels propelled in whole or in part by screw— (i) If the total propelling machinery space is 13 percent or less of the vessel's gross register tonnage, deduct 32/13 (ii) If the total propelling machinery space is more than 13 but less than 20 percent of the vessel's gross register tonnage, deduct 32 percent of the vessel's gross register tonnage; or (iii) If the total propelling machinery space is 20 percent or more of the vessel's gross register tonnage, deduct either 32 percent of the vessel's gross register tonnage or 1.75 times the total propelling machinery space, whichever the vessel owner elects. (3) For vessels propelled in whole or in part by paddle-wheel— (i) If the total propelling machinery space is 20 percent or less of the vessel's gross register tonnage, deduct 37/20 (ii) If the total propelling machinery space is more than 20 but less than 30 percent of the vessel's gross register tonnage, deduct 37 percent of the vessel's gross register tonnage; or (iii) If the total propelling machinery space is 30 percent or more of the vessel's gross register tonnage, deduct either 37 percent of the vessel's gross register tonnage or 1.5 times the total propelling machinery space, whichever the vessel owner elects. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989; 54 FR 40240, Sept. 29, 1989; USCG-2011-0522, 81 FR 18728, Mar. 31, 2016] § 69.123 Figures. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18728, Mar. 31, 2016] Subpart D —Dual Regulatory Measurements System § 69.151 Purpose. This subpart prescribes measurement requirements for the assignment of either one gross and one net register tonnage or two gross and two net register tonnages to vessels under this subpart. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.153 Application of other laws. (a) If a vessel is assigned two gross register tonnages under § 69.175(b), the higher gross register tonnage is the tonnage used when applying inspection, manning, and load line laws and regulations to the vessel. (b) Tonnage marks are not to be construed as additional load line marks. Whether or not a tonnage mark is submerged under § 69.171 has no effect on the applicability of load line laws and regulations. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.155 Measurement requirements. Except as otherwise required by this subpart, the measurement requirements under the Standard Regulatory Measurement System in subpart C of this part apply to the measurement of vessels under this subpart. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.157 Definitions. Terms used in this subpart that are defined in § 69.103 have the same meaning as in § 69.103, except the terms listed below. As used in this subpart,— Gross register tonnage Line for fresh and tropical waters Line of the second deck Line of the uppermost complete deck Net register tonnage Second deck (a) Is continuous athwartships and in a fore-and-aft direction at least between peak bulkheads, even though the deck may have interruptions or openings due to propelling machinery spaces, to hatch and ventilation trunks not extending longitudinally completely between main transverse bulkheads, to ladder and stairway openings, to chain lockers, or to cofferdams. (b) Is fitted as an integral and permanent part of the vessel. (c) Has proper covers to all main hatchways. (d) Does not have steps the total of which exceed 48 inches in height. Tonnage deck Tonnage mark [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.159 Application for measurement services. Applications for measurement services under this subpart must include the application information and plans required under § 69.105. The application must indicate whether a line for fresh and tropical waters is requested under § 69.177(b) and, for vessels with more than one deck, indicate whether one or two sets of tonnages are desired under § 69.175. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.161 Gross and net register tonnages. (a) Gross register tonnage (1) Under-deck tonnage (§ 69.163). (2) Between-deck tonnage (§ 69.165) (3) Superstructure tonnage (§ 69.167) (4) Excess hatchway tonnage (§ 69.115) (5) Tonnage of framed-in propelling machinery spaces included in calculating gross register tonnage (§ 69.121(d)(1)). (b) Net register tonnage (c) The authorized measurement organization must issue a U.S. Tonnage Certificate as evidence of a vessel's measurement under this subpart, which must also indicate the vessel's measurement under the Convention Measurement System in subpart B of this part, if applicable. There is no requirement to maintain the U.S. Tonnage Certificate on board the vessel. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.163 Under-deck tonnage. The under-deck tonnage provisions in § 69.109 apply; except that, under this subpart, spaces between the line of the tonnage deck and the tonnage deck itself due to a stepped tonnage deck are included in under-deck tonnage. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.165 Between-deck tonnage. The between-deck tonnage provisions in § 69.111 apply, except that, under this subpart, between-deck space extends from the tonnage deck to the uppermost complete deck, rather than from the line of the tonnage deck to the line of the uppermost complete deck. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.167 Superstructure tonnage. The superstructure tonnage provisions in § 69.113 apply; except that, under this subpart, spaces between the line of the uppermost complete deck and the uppermost complete deck itself due to a stepped uppermost complete deck are not included in the superstructure tonnage. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.169 Spaces exempt from inclusion in tonnage. The tonnage of the following spaces is exempt from inclusion in tonnage: (a) Spaces listed in § 69.117(b) when located within the superstructure. (b) Spaces listed in § 69.117(c)(1) through (c)(3) when located above, but not on, the uppermost complete deck. (c) Spaces listed in § 69.117(f), regardless of location. (d) Spaces available for carrying dry cargo and stores when located on or above the uppermost complete deck. (e) When a vessel is assigned a tonnage mark and the tonnage mark is not submerged,— (1) Spaces listed in § 69.117(b) when located between the uppermost complete deck and the second deck; (2) Spaces listed in § 69.117(c)(1) through (c)(3) when located on the uppermost complete deck; and (3) Spaces available for carrying dry cargo and stores when located between the uppermost complete deck and the second deck. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by CGD 92-058, 57 FR 59938, Dec. 17, 1992; USCG-2011-0522, 81 FR 18731, Mar. 31, 2016]

] § 69.171 When the tonnage mark is considered submerged. For the purpose of this subpart, a tonnage mark is considered submerged when— (a) In salt or brackish water, the upper edge of the tonnage mark is submerged; and (b) In fresh or tropical water, the upper edge of the line for fresh and tropical waters is submerged. § 69.173 Register Tonnage assignments for vessels with only one deck. A vessel without a second deck is assigned only one gross and one net register tonnage. In calculating the gross register tonnage, only the exemptions in § 69.169 (a) through (d) are allowed. Markings under § 69.177 are not permitted on these vessels. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.175 Tonnage assignments for vessels with a second deck. (a) At the option of the vessel owner, a vessel having a second deck is assigned either two gross and two net register tonnages or one gross and one net register tonnage corresponding to the lower gross and net register tonnages. (b) If two gross and two net register tonnages are assigned, the higher tonnages (i.e. those based only on exemptions under § 69.169 (a) through (d)) are applicable when the upper edge of the tonnage mark is submerged and the lower tonnages (i.e. those based only on all exemptions under § 69.169) are applicable when the upper edge of the tonnage mark is not submerged. (c) If only the low gross and low net register tonnages, as calculated under paragraph (b) of this section, are assigned, these tonnages are applicable at all times. On these vessels, a load line must be assigned at a level below the line of the second deck, and the tonnage mark must be located in accordance with § 69.177(a)(6) at the level of the uppermost part of the load line grid. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.177 Markings. (a) Tonnage mark. (2) The tonnage mark is a horizontal line 15 inches long and one inch wide. The tonnage mark must be designated by a welded bead or other permanent mark 15 inches long placed along the top edge of the tonnage mark. (3) Above the tonnage mark is placed an inverted equilateral triangle, each side of which is 12 inches long and one inch wide, with its apex touching the upper edge of the center of the tonnage mark. (4) If the vessel has a load line mark, the longitudinal location of the center of the tonnage mark must be between 21 inches and six feet six inches aft of the vertical centerline of the load line ring. (See the figures in § 69.183 (b) and (c).) If the vessel does not have a load line mark, the center of the tonnage mark must be located amidships. (5) Except as under paragraph (a)(6) of this section, the upper edge of the tonnage mark must be located below the line of the second deck at the distance indicated in Table 69.177(a)(5). (See the figure in § 69.183(b).) Table 69.177( a L (in feet) L divided by D 12 13 14 15 16 17 18 19 20 220 and under 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 230 3.2 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 240 4.7 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 250 6.3 3.3 2.0 2.0 2.0 2.0 2.0 2.0 2.0 260 8.0 4.8 2.1 2.0 2.0 2.0 2.0 2.0 2.0 270 9.9 6.4 3.5 2.0 2.0 2.0 2.0 2.0 2.0 280 11.8 8.1 4.9 2.1 2.0 2.0 2.0 2.0 2.0 290 13.9 9.9 6.5 3.5 2.0 2.0 2.0 2.0 2.0 300 16.0 11.7 8.1 4.9 2.1 2.0 2.0 2.0 2.0 310 18.3 13.7 9.8 6.4 3.5 2.0 2.0 2.0 2.0 320 20.7 15.8 11.7 8.1 4.9 2.1 2.0 2.0 2.0 330 23.2 18.0 13.6 9.8 6.4 3.5 2.0 2.0 2.0 340 25.9 20.4 15.7 11.6 8.1 4.9 2.1 2.0 2.0 350 28.7 22.9 17.9 13.6 9.8 6.5 3.6 2.0 2.0 360 31.7 25.5 20.2 15.7 11.7 8.2 5.0 2.2 2.0 370 34.7 28.3 22.7 17.9 13.6 9.9 6.6 3.7 2.0 380 38.0 31.1 25.3 20.2 15.7 11.8 8.3 5.2 2.4 390 41.3 34.1 27.9 22.6 17.9 13.8 10.1 6.8 3.8 400 44.8 37.2 30.7 25.0 20.1 15.8 11.9 8.4 5.3 410 48.2 40.3 33.5 27.7 22.6 18.1 14.0 10.4 7.2 420 51.5 43.4 36.4 30.4 25.2 20.6 16.4 12.7 9.7 430 54.8 46.5 39.4 33.3 27.9 23.2 19.0 15.2 11.8 440 58.4 49.9 42.6 36.4 30.9 26.0 21.7 17.8 14.4 450 62.1 53.4 46.0 39.6 33.9 29.0 24.6 20.6 17.1 460 65.9 57.0 49.5 42.9 37.1 32.1 27.6 23.5 19.9 470 69.8 60.7 53.0 46.3 40.4 35.2 30.6 26.5 22.8 480 73.7 64.4 56.5 49.7 43.7 38.4 33.7 29.5 25.7 490 77.5 68.1 60.0 53.0 46.9 41.5 36.7 32.4 28.5 500 81.2 71.6 63.4 56.2 50.0 44.5 39.6 35.2 31.2 510 84.9 75.1 66.7 59.4 53.0 47.4 42.4 37.9 33.9 520 88.4 78.4 69.9 62.4 55.9 50.2 45.1 40.5 36.4 530 91.8 81.6 72.9 65.3 58.7 52.9 47.7 43.0 38.8 540 95.2 84.8 75.9 68.1 61.4 55.5 50.2 45.4 41.2 550 98.4 87.8 78.8 70.9 64.0 58.0 52.6 47.8 43.4 560 101.6 90.8 81.6 73.6 66.6 60.5 55.0 50.1 45.6 570 104.8 93.8 84.4 76.3 69.2 62.9 57.3 52.3 47.8 580 107.9 96.8 87.2 78.9 71.7 65.3 59.6 54.5 49.9 590 111.0 99.7 90.0 81.5 74.2 67.7 61.9 56.7 52.0 600 114.0 102.5 92.6 84.0 76.5 69.9 64.0 58.8 54.0 610 117.0 105.3 95.2 86.5 78.9 72.1 66.2 60.8 56.0 620 120.0 108.0 97.8 88.9 81.2 74.4 68.3 62.8 58.0 630 122.9 110.7 100.4 91.3 83.5 76.6 70.4 64.8 59.9 640 125.7 113.4 102.9 93.7 85.8 78.7 72.4 66.8 61.7 650 128.6 116.1 105.4 96.1 88.0 80.8 74.4 68.7 63.6 660 131.4 118.7 107.8 98.3 90.1 82.8 76.3 70.6 65.3 670 134.2 121.2 110.2 100.6 92.2 84.8 78.3 72.4 67.1 680 136.9 123.8 112.8 102.9 94.3 86.8 80.2 74.2 68.9 690 139.6 126.3 115.0 105.1 96.4 88.8 82.1 76.0 70.6 700 142.3 128.8 117.3 107.3 98.5 90.8 83.9 77.8 72.3 710 144.9 131.3 119.6 109.4 100.5 92.7 85.7 79.5 73.9 720 147.5 133.7 121.8 111.5 102.5 94.6 87.5 81.2 75.5 730 150.1 136.1 124.0 113.6 104.5 96.5 89.3 82.9 77.1 740 152.7 138.5 126.2 115.7 106.5 98.3 91.5 84.5 78.7 750 155.3 140.8 128.5 117.8 108.4 100.1 92,8 86.1 80.3 760 157.8 143.1 130.6 119.7 110.3 101.9 94.4 87.8 81.7 770 160.2 145.4 132.7 121.7 112.1 103.6 96.0 89.3 83.2 780 162.6 147.6 134.8 123.7 113.9 105.3 97.6 90.8 84.7 790 165.1 149.9 136.9 125.6 115.7 107.0 99.2 92.3 86.1 800 167.5 152.1 138.9 127.4 117.4 108.6 100.8 93.8 87.4 L = the length in feet of the line of the second deck at the centerline of the vessel from the inner surface of the frames at the vessel's stem to the inner surface of the frames at the vessel's stern. D = The vertical distance in feet from the top of the flat keel of the vessel to the line of the second deck. EXAMPLE (1) For a vessel in which L = 450 feet and L/D = 15 feet, read down from the L/D column “15” and to the right on the column “450” to where the two columns intersect at 39.6. The tonnage mark must be located 39.6 inches below the line of the second deck. EXAMPLE (2) If L or L/D is an intermediate number, the distance “a” between the tonnage mark and the line of the second deck must be obtained by linear interpolation. For a vessel in which L = 424.80 feet and L/D = 15.17: L Table L/D = 15 Actual L/D = 15.17 Table L/D = 16 Table 420 30.4 25.2 Actual 424.80 r a s Table 430 33.3 27.9 Interpolation: r = 30.4 + 0.48 (33.3−30.4) = 31.79 s = 25.2 + 0.48 (27.9−25.2) = 26.50 a = r−0.17 (r−s) = 31.79−0.17 (31.79−26.50) = 30.89 inches (6) For the following vessels with a load line mark, the upper edge of the tonnage mark must be located at the level of the uppermost part of the load line grid: (i) Vessels assigned only one gross and one net register tonnage under § 69.175(c). (ii) Vessels for which a load line assigning authority certifies that the vessel's load line mark was located as though the second deck were the freeboard deck. (b) Line for fresh and tropical waters. (2) The line must be nine inches long and one inch wide and located above and to the left of the tonnage mark at a distance equal to one forty-eighth of the distance from the top of the flat keel to the tonnage mark. The tonnage mark and the line for fresh and tropical waters must be connected by a vertical line one inch wide. (See the figure in § 69.183(a).) (3) The line for fresh and tropical waters must be designated by a welded bead or other permanent mark nine inches long placed along the upper edge of the line. (4) For vessels with a load line mark, if the load line assigning authority certifies that the load line mark was located as though the second deck were the freeboard deck, a line for fresh and tropical waters must not be placed on the vessel. (c) Freeboard deck mark. (d) The line of the second deck. (e) Color of markings. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.179 Certification of markings. (a) Before a certificate of measurement is issued for a vessel requiring a tonnage mark, a certification by a measurement organization under § 69.15 that all markings meet the requirements of this subpart is required. (b) The Coast Guard, at any time, may verify markings under this subpart. § 69.181 Locating the line of the second deck. (a) If the second deck is not stepped, the line of the second deck is the longitudinal line of the underside of the second deck at the side of the hull. (b) If the second deck is stepped (as in the examples following this paragraph), the line of the second deck is a longitudinal line extended parallel to each portion of the second deck and located at the height of the underside of the amidships portion of the second deck at the side of the hull— (1) Plus, for each stepped portion of the second deck higher than the second deck at amidships, a distance equal to the length of the stepped portion divided by the total length of the second deck times the height that the step is above the height of the amidship portion of the second deck; and (2) Minus, for each stepped portion of the second deck lower than the second deck at amidships, a distance equal to the length of the stepped portion divided by the total length of the second deck times the height that the amidship portion of the second deck is above the height of the step. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18731, Mar. 31, 2016] § 69.183 Figures. (a) Tonnage mark with an equilateral triangle and a line for fresh and tropical waters. W= 1/48 (b) Tonnage mark location if the load line mark is not placed as though the second deck were the freeboard deck. k = a distance between 21 inches and six feet six inches. a = distance derived from Table 69.177(a)(5). (c)— Tonnage mark location if the load line mark is placed as though the second deck were the freeboard deck. k = a distance between 21 inches and six feet six inches. a = the distance between the line of the second deck and the uppermost part of the load line grid. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18732, Mar. 31, 2016] Subpart E—Simplified Regulatory Measurement System § 69.201 Purpose. This subpart prescribes the procedures for measuring a vessel under the Simplified Regulatory Measurement System described in 46 U.S.C. chapter 145, subchapter III. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18732, Mar. 31, 2016] § 69.203 Definitions. As used in this subpart and in Coast Guard Form CG-5397 under § 69.205— Overall breadth Overall depth Overall length Registered breadth (a) For a single-hull vessel, the vessel's overall breadth; and (b) For a multi-hull vessel, the horizontal distance taken at the widest part of the complete vessel between the outboard side of the skin (outside planking or plating) on the outboardmost side of one of the outboardmost hulls to the outboard side of the skin on the outboardmost side of the other outboardmost hull, excluding rubrails. Registered depth (a) For a single-hull vessel, the vessel's overall depth; and (b) For a multi-hull vessel, the overall depth of the deepest hull. Registered length (a) For a single-hull vessel, the vessel's overall length; and (b) For a multi-hull vessel, the horizontal distance between the outboard side of the foremost part of the stem of the foremost hull and the outboard side of the aftermost part of the stern of the aftermost hull, excluding fittings or attachments. Vessel designed for sailing [CGD 87-015b, 54 FR 37657, Sept. 12, 1989; 54 FR 40240, Sept. 29, 1989; USCG-1999-6216, 64 FR 53225, Oct. 1, 1999] § 69.205 Application for measurement services. (a) Except as noted under paragraph (c) of this section, to apply for measurement under this subpart, the vessel owner must complete an Application for Simplified Measurement (form CG-5397). If the vessel is documented, or intended to be documented, as a vessel of the United States under part 67 of this chapter, the vessel owner must submit the application form to the National Vessel Documentation Center. Otherwise, the form is not further processed, but may be retained, at the vessel owner's option, as evidence of the tonnage measurement under this part. (b) The Application for Simplified Measurement (form CG-5397) must include the following information: (1) Vessel's name and number (e.g., official number, International Maritime Organization (IMO) number, or Coast Guard number). (2) Vessel hull identification number or other number assigned by builder. (3) Hull material. (4) Hull shape. (5) Overall length, breadth, and depth of vessel and each of the vessel's individual hulls. (6) Location of any propelling machinery (e.g., inside or outside of the hull). (7) Dimensions of the principal deck structure, if its volume exceeds the volume of the hull. (c) At the vessel owner's option, a Builder's Certification and First Transfer of Title (form CG-1261), which includes the same information specified in paragraph (b) of this section may be submitted to the National Vessel Documentation Center instead of the Application for Simplified Measurement for a vessel that is documented, or intended to be documented, as a vessel of the United States under part 67 of this chapter. [USCG-2011-0522, 81 FR 18733, Mar. 31, 2016] § 69.207 Measurements. (a) All lengths and depths must be measured in a vertical plane at centerline and breadths must be measured in a line at right angles to that plane. All dimensions must be expressed in feet and inches to the nearest inch or in feet and tenths of a foot to the nearest tenth of a foot. (b) For a multi-hull vessel, each hull must be measured separately for overall length, breadth, and depth and the vessel as a whole must be measured for registered length, breadth, and depth. (c) The Coast Guard may verify dimensions of vessels measured under this subpart. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by USCG-2011-0522, 81 FR 18734, Mar. 31, 2016] § 69.209 Gross and net register tonnages. (a) Gross register tonnage. (2) The gross tonnage of a vessel with a hull that approximates in shape a rectangular geometric solid (barge-shape) is 0.84 LBD/100. (3) The gross tonnage of a multi-hull vessel is the sum of all the hulls as calculated under this section. (4) If the volume of the principal deck structure of a vessel is as large as, or larger than, the volume of the vessel's hull, the volume of the principal deck structure in tons of 100 cubic feet is added to the tonnage of the hull to establish the vessel's gross tonnage. The volume of the principal deck structure of a vessel is determined by the product of its average dimensions. (5) If the overall depth of a vessel designed for sailing includes the keel, only 75 percent of that depth is used for gross tonnage calculations. (b) Net register tonnage. (i) The net register tonnage is 90 percent of its gross register tonnage, if it is a vessel designed for sailing; or (ii) The net register tonnage is 80 percent of its gross register tonnage, if it is not a vessel designed for sailing. (2) For a vessel having no propelling machinery in its hull, the net register tonnage is the same as its gross register tonnage. (c) Certification of measurement. [CGD 87-015b, 54 FR 37657, Sept. 12, 1989, as amended by CGD 97-057, 62 FR 51045, Sept. 30, 1997; USCG-2011-0522, 81 FR 18734, Mar. 31, 2016] § 69.211 Treatment of novel type vessels. Refer questions regarding the application of the tonnage measurement rules under this subpart to novel type vessels to the Commandant. [USCG-2011-0522, 81 FR 18734, Mar. 31, 2016]

Related documents

• 50 CFR Part 600 — Magnuson-Stevens Act Provisions#512148
• 50 CFR Part 622 — Fisheries of the Caribbean, Gulf of America, and South Atlantic#512149
• 50 CFR Part 635 — Atlantic Highly Migratory Species#512150
• 50 CFR Part 648 — Fisheries of the Northeastern United States#512151
• 50 CFR Part 660 — Fisheries off West Coast States#512152