additive-manufacturing

Documents about additive-manufacturing

• Imperfections Formation in Thin Layers of NiTi Triply Periodic Minimal Surface Lattices Fabricated Using Laser Powder Bed Fusion#20750HAL (France)
• Quadcopter Unmanned Aerial Vehicle Structural Design Using an Integrated Approach of Topology Optimization and Additive Manufacturing#8890HAL (France)
• Multiaxial fatigue behaviour of alloys obtained by additive manufacturing : influence of defects#126830HAL (France)
• FDM-Bench: A Comprehensive Benchmark for Evaluating Large Language Models in Additive Manufacturing Tasks#144238arXiv (OAI)
• Additive Manufacturing of Broadband Dielectric Resonator Antennas Using Graded Permittivity and Modal Analysis#153738HAL (France)
• Effect of additive manufacturing process parameters on the titanium alloy microstructure, properties and surface integrity#178185HAL (France)
• Biocompatible and bioactive PEG-Based resin development for additive manufacturing of hierarchical porous bone scaffolds#260584Repositorio USS
• Additive manufacturing of high-strength aluminium alloys for thermal management applications#328217UBIRA ETheses
• 2023_Sos-Bruder_MaterDes_AlSi10Mg-lattices#331698TUdatalib System
• Microstructure and micromechanical properties of microcellular AlSi10Mg produced via LPBF#374439HAL (France)
• Development of low alloy steel by direct metal laser sintering#641339Digital Commons @ NJIT
• Elastoplastic inherent strain-based topology optimization for residual stress reduction in metal additive manufacturing#984266arXiv (All)
• Design and Fabrication of Superhydrophobic Porous Structures via 3D Printing and Phase Separation for Oil–Water Separation#284159HAL (France)
• Edge-focused wire arc additive manufacturing: Method development with ANN-based stress-strain and mass-efficiency.#265327NCBI PubMed Central
• Comprehensive Review of Research Progress on Trajectory Planning and Weld Seam Tracking in Wire Arc Additive Manufacturing.#319222NCBI PubMed Central
• A Non-Line-of-Sight, Multi-Modality-based Side-Channel IP Theft Attack on Additive Manufacturing Using Dual Smartphones#329038arXiv CS
• Engineering Porous PET-RAFT Scaffolds with PLGA–Insulin Nanoparticles : Advancing Bone Tissue Regeneration Through Additive Manufacturing#336274Repositorio USS
• Metal Additive Manufacturing of Smart and Functional Materials: A Comprehensive Review#395313HAL (France)
• Design and Application of Additive Manufacturing#486735Directory of Open Access Books
• ADDITIVELY MANUFACTURED SPIRALLY CORRUGATED HEAT EXCHANGER TUBES#633671Calhoun
• Influence of process parameters on stability, surface roughness, and defect formation in wire laser additive manufacturing at high deposition rate#347865HAL (France)
• <b>Achieving strength</b><b>-</b><b>ductility synergy of lamellar heterostructured dual-phase Titanium alloy via laser powder bed fusion</b>#454394Figshare
• Improving the fatigue performance of additively manufactured Ti6Al4V alloy through surface shocking#194907Recep Tayyip Erdoğan University Institutional Repository
• 2D profile-based surface repair and 3D pattern generative design via material jetting#288072HAL (France)
• Hybrid additive manufacturing-based assembly of sacrificial isomalt scaffolds and gas exchange membranes for microfluidic artificial lung development.#295237NCBI PubMed Central
• Additive Manufacturing of Ti6Al4V Using Directed Energy Deposition: An Elaborative Approach of Process Modelling via Computational Fluid Dynamics#417097Aperta
• Characterizing and Modeling the Nonlinear Behavior of Additively Manufactured Trapped-Powder Dampers#623363BYU ScholarsArchive
• A statistical decomposition of geometric imperfections applied to robust topology optimisation#643199HAL (France)
• Advancing transistor-based point-of-care (POC) biosensors: additive manufacturing technologies and device integration strategies for real-life sensing.#251388NCBI PubMed Central
• Impact of applied loads on wear mechanisms in H13 steel at various preheating temperatures during laser powder bed fusion additive manufacturing#257574HAL (France)
• Optimizing additive manufacturing path pattern for Ti-6Al-4V thin rods using a combinatorial radial basis function surrogate-assisted genetic algorithm#304495HAL (France)
• Towards deeper carburizing by DEDp and L-PBF additive manufacturing of in-situ TiC-reinforced steel composites: powders and processability#330098HAL (France)
• Investigation of mechanical metamaterials additively manufactured using pulsed laser fusion of metal sheets#377538DR-NTU (Digital Repository of NTU)
• AN ASSESSMENT OF GYROID TRIPLY PERIODIC MINIMAL SURFACES FOR ADDITIVELY MANUFACTURED HEAT EXCHANGERS#633674Calhoun
• Evaluation of CAD/CAM Onlays Fabricated by Subtractive Versus Additive Digital Manufacturing Techniques.#829609ClinicalTrials.gov
• Engineering Design and Analysis using Creo® CAD, CAE, and Manufacturing Applications#168752Digital Commons @ NJIT
• Mechanical Analysis of Thick-Walled Low-Carbon Steel Structures Produced by Wire Arc Additive Manufacturing with Zig-Zag Trajectories#254261HAL (France)
• Laser powder bed fusion additive manufacturing of high-strength hot tool steel via in-situ heat treatment induced nano-scaled strengthening mechanism#257578HAL (France)
• Cost-Effective Experiments With Additively Manufactured Waveguide and Cavities in the S-Band#1027153İzmir Yüksek Teknoloji Enstitüsü
• Design and optimization of next-generation composite materials through additive manufacturing : towards revolutionary mechanical#124440HAL (France)
• Modelling and control of soft-rigid actuator for assistive technologies#447214University of Nottingham Repository
• A Full Polymer Piezoelectric Flextensional Energy Harvester#653849ODU Digital Commons
• Toward accurate fused deposition modeling 3D printer fault detection using improved YOLOv8 with hyperparameter optimization#1042815Animo Repository
• Introduction to Computer-Aided Design Using SOLIDWORKS® : A Structured Approach to Parametric Modeling and Design Intent#168751Digital Commons @ NJIT
• Optimizing porosity detection in wire laser metal deposition processes through data-driven AI classification techniques#8132HAL (France)
• Improving crack reduction by tailoring minor element content in γ/γ′ cobalt-based superalloys processed by directed energy deposition#254292HAL (France)
• The cell in the ink.improving biofabrication by printing stem cells for skeletal regenerative medicine#254402IRIS
• Environmental implications of feedback-controlled heat input in wire arc additive manufacturing of Invar 36 through online contact tip-to-workpiece distance adjustment#442670IRIS
• Exploiting triply periodic minimal surfaces with robocasted bioceramics and cements for bone regeneration: Current strategies and opportunities#471958HAL (France)
• Recent Advances in Hydrogel-Based 3D Disease Modeling and Drug Screening Platforms#681778İzmir Yüksek Teknoloji Enstitüsü