PART 1220—SAFETY STANDARD FOR NON-FULL-SIZE BABY CRIBS Authority: 15 U.S.C. 2056a. Source: 75 FR 81787, Dec. 28, 2010, unless otherwise noted. § 1220.1 Scope, compliance dates, and definitions. (a) Scope. (b) Compliance dates. (2) Child care facilities, family child care homes, and places of public accommodation affecting commerce shall be required to comply with this part on December 28, 2012, but this provision applies only to the offer or provision for use of cribs by child care facilities, family child care homes, and places of public accommodation affecting commerce and not the sale, resale, or other placement in the stream of commerce of cribs by these entities. (c) Definitions. Non-full-size baby crib (i) Designed to provide sleeping accommodations for an infant; (ii) Intended for use in or around the home, for travel, in a child care facility, in a family child care home, in a place of public accommodation affecting commerce and other purposes; (iii) Has an interior length dimension either greater than 139.7 cm (55 in.) or smaller than 126.3 cm (49 3/4 5/8 3/8 (iv) Includes, but is not limited to, the following: (A) Portable crib (B) Crib pen (C) Specialty crib (D) Undersize crib 3/4 3/8 (E) Oversize crib 5/8 (v) Does not include mesh/net/screen cribs, nonrigidly constructed baby cribs, cradles (both rocker and pendulum types), car beds, baby baskets, and bassinets (also known as junior cribs). (2) Play yard (3) Place of public accommodation affecting commerce § 1220.2 Requirements for non-full-size baby cribs. (a) Except as provided in paragraph (b) of this section, each non-full-size baby crib shall comply with all applicable provisions of ASTM F406-24, Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards, [email protected]. [email protected], www.archives.gov/federal-register/cfr/ibr-locations. www.astm.org/READINGLIBRARY/. www.astm.org. (b) Comply with the ASTM F406-24 standard with the following exclusions: (1) Do not comply with sections 5.6.2 through 5.6.2.4 of ASTM F406-24. (2) Do not comply with section 5.16.2 of ASTM F406-24. (3) Do not comply with sections 5.19 through 5.19.2.2 of ASTM F406-24. (4) Do not comply with section 7, Performance Requirements for Mesh/Fabric Products, (5) Do not comply with sections 8.11 through 8.11.2.4 of ASTM F406-24. (6) Do not comply with sections 8.12 through 8.12.2.2 of ASTM F406-24. (7) Do not comply with sections 8.14 through 8.14.2 of ASTM F406-24. (8) Do not comply with sections 8.15 through 8.15.3.3 of ASTM F406-24. (9) Do not comply with sections 8.16 through 8.16.3 of ASTM F406-24. (10) Do not comply with sections 8.28 through 8.28.3.2 of ASTM F406-24. (11) Do not comply with sections 8.29 through 8.29.3 of ASTM F406-24. (12) Do not comply with sections 8.30 through 8.30.5 of ASTM F406-24. (13) Do not comply with sections 8.31 through 8.31.9 of ASTM F406-24. (14) Do not comply with sections 9.6.1 through 9.6.1.4 of ASTM F406-24. [90 FR 8682, Jan. 31, 2025, as amended at 90 FR 9608, Feb. 14, 2025]